Kemtron Hydrocyclone Parts | KTH Apex, Nut & Insert

2026-11-07 21:25

Key Facts



Primary Wear Parts (4" Cone)Body (KTH-4-002), Apex Nut (KTH-4-003), Apex Insert (KTH-4-004)
Secondary Wear PartsInlet (KTH-4-001), Clamp (KTH-4-005), Elbow (KTH-GL-203)
Compatible ConesKemtron 4" Desilter, 5" Desilter, 10" Desander, 12" Desander
MaterialHigh-durometer polyurethane; ceramic inserts available
Inspection CycleEvery 500–1,000 operating hours (typical)
Replacement TriggerCoarse underflow spray or cut-point drift

Wear Parts by Configuration

4-inch Kemtron Desilter Cone (KTH-4-00x System)

Part NameReference Part No.Function
4" InletKTH-4-001Cone inlet section
4" BodyKTH-4-002Main cone body; replace if deep grooving occurs
Apex NutKTH-4-003Controls underflow opening
Apex Wear InsertKTH-4-004Primary wear part; replace when underflow coarsens
Stainless Steel ClampKTH-4-005Manifold clamp
2" Groove Lock ElbowKTH-GL-203Overflow routing

5" / 10" / 12" Kemtron Cones

Part NameReference Part No.Notes
5" Desilter ComponentsVerify against drawingApex, nut, wear parts available upon request
10" Desander ComponentsVerify against drawingApex and wear sections available upon request
12" Desander ComponentsVerify against drawingApex and wear sections available upon request

Data source: Technical data and parts list.

Wear Inspection Guidance (Symptoms & Actions)

A hydrocyclone's cut point drifts when the apex insert or body erodes. Instead of guessing a replacement date, monitor the underflow pattern.

  • Normal Operation: The underflow should discharge in a tight, cone-shaped spray (about 20–30°).
  • Worn Apex Insert (KTH-4-004): The spray becomes coarse or rope-like. Replace the insert to restore the original underflow opening.
  • Worn Body (KTH-4-002): Look for visible grooves or material loss on the inside of the cone body. Severe erosion changes the internal geometry and disrupts the centrifugal pattern.
  • Action: Shut off the individual cone's isolation valve, remove the wear part, and inspect. Replace the KTH-4-004 insert or KTH-4-003 nut if wear is visible.

Maintenance Tip: Inspect wear parts every 500–1,000 operating hours. In high-sand HDD formations, check more frequently between bores to avoid unplanned downtime.

Cross-Reference & Replacement

Upgrading a worn Kemtron wear part? Here's how to ensure a drop-in fit:

  1. Confirm the Cone Size: 4" cones use the KTH-4-00x system; 5", 10", and 12" cones require dimension verification against your existing Kemtron header.
  2. Verify Threads and Grooves: Check that the KTH-4-003 nut threads and KTH-GL-203 elbow grooves are not cross-threaded or stripped before installing the new wear part.
  3. Select Material: Standard urethane suits most HDD muds. For abrasive sand, specify ceramic inserts.

Not interchangeable with: Apexes or bodies designed for non-Kemtron manifold patterns or different cone sizes without verifying dimensions.

Compatible Host Models

These wear parts are compatible with:

  • Kemtron HDD 400 Pro (4" desilter cones)
  • Kemtron HDD 1000 Pro (12" desander + 5" desilter cones)
  • Kemtron HDD 1500HDX (10" desander + 5" desilter cones)

To select a complete cone assembly, view the Kemtron 4" & 5" desilter cone compatible replacement or the Kemtron 10" & 12" desander cone compatible replacement. For the full range overview, see Kemtron-compatible hydrocyclones.

Selection Support

Not sure which KTH-4-00x component is worn, or whether a ceramic insert is available for your 5", 10", or 12" cone? Send us a photo of the current wear part and the cone body, and we will confirm the exact replacement part number before you order.

Frequently Asked Questions

Q1: Are these original Kemtron replacement parts?
A: No. HYRIG supplies independent, compatible wear parts and is not affiliated with or endorsed by Elgin Separation Solutions or Astec.

Q2: How do I know when to replace the apex insert (KTH-4-004)?
A: Replace when the underflow spray becomes coarse or rope-like, usually after 500–1,000 operating hours.

Q3: Can I replace just the KTH-4-004 insert without buying a full cone body?
A: Yes. The KTH-4-004 insert, KTH-4-003 nut, and KTH-4-005 clamp are designed for standalone replacement.

Q4: Do you offer ceramic inserts for Kemtron cones?
A: Yes. Ceramic inserts are available for 4", 5", 10", and 12" cones to extend wear life in abrasive HDD formations.

Q5: What is the lead time for a replacement KTH component?
A: Standard urethane wear parts ship in 1–2 weeks. Order before project start dates to avoid downtime between bores.

Contact

For Kemtron-compatible hydrocyclone wear parts selection, contact HYRIG: info@hyrig.com

What to include for fastest quote:

  • Current KTH part number or a photo of the worn part
  • Cone size (4", 5", 10", or 12")
  • Required quantity
  • Destination port
Name:
Message:
Verification code:
Submit
Comment