| Cone Sizes | 4-inch and 5-inch Desilter |
| 4" Part Number System | KTH-4-001 (Inlet), KTH-4-002 (Body), KTH-4-003 (Apex Nut), KTH-4-004 (Apex Insert), KTH-4-005 (Clamp) |
| 5" Flow Capacity | 75–85 GPM per cone |
| Separation Stage | Fine silt removal (desilter) |
| Body Material | High-durometer polyurethane; ceramic inserts optional |
| Compatible Host | Kemtron 400 Pro (4"), 1000 Pro (5"), 1500HDX (5") |
| Manifold Connection | 2" grooved-end (4" cone, KTH-GL-203 elbow) |
| Replacement Compatibility | Drop-in replacement for Kemtron HDD desilter manifolds |
| Parameter | 4" Desilter Cone | 5" Desilter Cone |
|---|---|---|
| Reference Part No. | KTH-4-002 (Body) | Verify against drawing |
| Cone diameter | 4 in (102 mm) | 5 in (127 mm) |
| Flow capacity | 50–65 GPM | 75–85 GPM |
| Application | Desilter (fine silt) | Desilter (fine silt) |
| Body material | Urethane; ceramic insert optional | Urethane; ceramic insert optional |
| Associated elbow | KTH-GL-203 (2" grooved-end) | Verify against drawing |
| Compatible host | Kemtron 400 Pro | Kemtron 1000 Pro / 1500HDX |
Data source: Technical data table.
| Dimension | 4" Cone | 5" Cone |
|---|---|---|
| Overall height | Matches KTH-4-002 body | Matches Kemtron 5" manifold |
| Cone body OD | 4 in (102 mm) | 5 in (127 mm) |
| Manifold interface | 2" grooved-end (KTH-GL-203) | Verify against existing header |
| Weight (approx.) | 4–6 kg | Verify against drawing |
Drilling mud enters the desilter cone tangentially through the inlet. Centrifugal force drives silt-sized solids to the polyurethane wall and down through the apex as underflow, while clarified fluid exits upward through the vortex finder. In HDD operations, the 4" and 5" desilter cones polish the mud after the desander stage, removing fine particles that would otherwise damage downhole tools or block the bore path.
The 4" Kemtron cone is built as a modular assembly. The inlet (KTH-4-001), body (KTH-4-002), apex nut (KTH-4-003), apex wear insert (KTH-4-004), and stainless steel clamp (KTH-4-005) are all replaceable individually. This means a worn apex insert does not require replacing the entire cone body—a critical cost-saving feature for HDD contractors running multiple bores per week.
Replacing a Kemtron desilter cone? Check these points before ordering:
Not interchangeable with: 10" or 12" desander cones, or desilter cones from non-Kemtron manifold patterns, without verifying inlet and outlet dimensions first.
For 10" and 12" desander cones used ahead of the desilter stage, see Kemtron 10" & 12" desander cone compatible replacement. For the full range, see Kemtron-compatible hydrocyclones.
Not sure whether your Kemtron system uses 4" or 5" desilters, or which KTH-4-00x component is worn? Send us a photo of the cone body and the part number stamped on the component, and we will confirm the matching replacement before you order.
HYRIG provides replacement wear components for Kemtron 4" and 5" desilter cones:
| Part Name | Reference Part No. | Notes |
|---|---|---|
| 4" Inlet | KTH-4-001 | Cone inlet section |
| 4" Body | KTH-4-002 | Main cone body |
| Apex Nut | KTH-4-003 | Underflow control |
| Apex Wear Insert | KTH-4-004 | Replaceable wear insert |
| Stainless Steel Clamp | KTH-4-005 | Manifold clamp |
| 2" Groove Lock Elbow | KTH-GL-203 | Overflow elbow |
| 5" Desilter Components | Verify against drawing | Apex, nut, and wear parts available upon request |
Qty as per parts list; verify against original drawing. For wear-part inspection guidance, see Kemtron hydrocyclone wear parts.
Q1: Is this an original Kemtron product?
A: No. HYRIG supplies independent, compatible replacement products and is not affiliated with, authorized by, or endorsed by Elgin Separation Solutions or Astec.
Q2: How do I know if I need a 4" or 5" desilter cone?
A: Kemtron 400 Pro uses 4" desilters; 1000 Pro and 1500HDX use 5" desilters. Check your system model and manifold layout.
Q3: Can I replace just the apex insert (KTH-4-004) without buying a full cone?
A: Yes. The KTH-4-004 insert and KTH-4-003 nut are designed for standalone replacement.
Q4: What is the lead time for Kemtron desilter cones?
A: Standard urethane cones ship in 2–3 weeks. Ceramic inserts may require 4–5 weeks. Plan ahead for project start dates.
Q5: What should I inspect if the cone stops holding cut point?
A: Check the apex insert (KTH-4-004) for erosion and the nut (KTH-4-003) for thread wear. A worn insert is the most common cause of coarse underflow.
For Kemtron 4" / 5" desilter cone selection and compatible replacement parts, contact HYRIG: info@hyrig.com
What to include for fastest quote:
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.