SWACO 12" Desander Cone Parts | 9621280 Wear Parts

2026-11-07 21:25

Key Facts



Primary Wear PartsBody Cone (96-21-173), Feed Section (96-21-281)
Compatible Cones12" Desander (9621280)
MaterialPolyurethane
Inspection CycleEvery 500–1,000 operating hours (typical)
Replacement TriggerCoarse underflow spray or cut-point drift

Wear Parts by Configuration

12-inch Desander Cone (9621280 Compatible)

Part NameReference Part No.Function
Body Cone 12"96-21-173Main internal cone body; replace if deep grooving occurs
Feed 12"96-21-281Directs mud into the cone; inspect for inlet wear
ApexVerify against drawingControls underflow rate

Data source: Technical data and parts list.

Wear Inspection Guidance (Symptoms & Actions)

A hydrocyclone's cut point drifts when the apex or internal body erodes. Instead of guessing a replacement date, monitor the underflow pattern.

  • Normal Operation: The underflow should discharge in a tight, cone-shaped spray (about 20–30°).
  • Worn Apex: The spray becomes coarse or rope-like. This means the opening has enlarged, letting finer solids bypass to the overflow.
  • Worn Body Cone (96-21-173): Look for visible grooves or material loss on the inside of the cone body. Severe erosion changes the internal geometry and disrupts the centrifugal pattern.
  • Action: Shut off the cone's feed valve, remove the apex/body, and inspect. Replace the body cone (96-21-173) if grooving is visible.

Maintenance Tip: Inspect wear parts every 500–1,000 operating hours. In high-sand formations, check more frequently during year-end shutdowns to avoid unplanned downtime.

Cross-Reference & Replacement

Upgrading a worn wear part? Here's how to ensure a drop-in fit:

  1. Confirm the Cone Size: The 12" cone uses the 96-21-173 body cone and 96-21-281 feed section.
  2. Verify Connections: Check that the grooved-end connection is not worn or damaged before installing the new wear part.
  3. Select Material: Standard polyurethane suits most water-based and oil-based muds. For high-abrasive sand, consider a ceramic option if available.

Not interchangeable with: Apexes or body cones designed for non-M-I SWACO manifold patterns or smaller (4") desilter bodies without verifying dimensions.

Compatible Host Models

These wear parts are compatible with:

  • M-I SWACO D-Sander units with 12" cone manifolds
  • M-I SWACO Mongoose series mud cleaners with a desander stage

To select a complete cone assembly, view the 12" desander cone 9621280 compatible replacement. For the full range overview, see M-I SWACO-compatible hydrocyclones.

Selection Support

Not sure whether you need the full body cone (96-21-173) or just the feed section (96-21-281), or whether the grooves on your manifold are still serviceable? Send us a photo of the current wear part and the cone body, and we will confirm the exact replacement part number before you order.

Frequently Asked Questions

Q1: Are these original M-I SWACO replacement parts?
A: No. HYRIG supplies independent, compatible wear parts and is not affiliated with or endorsed by M-I SWACO or Schlumberger.

Q2: How do I know when to replace the body cone or feed section?
A: Replace when the underflow spray becomes coarse or rope-like, usually after 500–1,000 operating hours.

Q3: Can I replace just the body cone without replacing the whole assembly?
A: Yes. The 96-21-173 body cone and 96-21-281 feed section are designed for standalone replacement.

Q4: What is the lead time for a replacement body cone?
A: Standard polyurethane wear parts ship in 1–2 weeks. Order before year-end shutdowns to avoid rig downtime.

Contact

For M-I SWACO-compatible hydrocyclone wear parts selection, contact HYRIG: info@hyrig.com

What to include for fastest quote:

  • Current part number or a photo of the worn part
  • Cone size (12")
  • Required quantity
  • Destination port
Name:
Message:
Verification code:
Submit
Comment