12" Desander Cone | SWACO 9621280 Compatible Replacement

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
This 12-inch desander cone is a drop-in compatible replacement for the M-I SWACO 9621280 assembly, rated at 500 GPM per cone at 45 PSI. It is used in primary solids control to remove sand-sized particles in the 40–100 μm range ahead of the desilter stage. The polyurethane cone body and grooved-end connection match the original D-Sander installation dimensions, so existing pipework and manifold brackets require no alteration. HYRIG supplies independent, compatible replacement products for M-I SWACO desander installations; we are not affiliated with, authorized by, or endorsed by M-I SWACO or Schlumberger.
Conatct For Details
DetailReview(0)Additional

Key Facts



Cone Size12 inches
Replacement Part No.M-I SWACO 9621280
Flow Capacity500 GPM at 45 PSI
Separation Range40–100 μm
Cone MaterialPolyurethane
Max PressureVerify against manifold pressure
Compatible HostM-I SWACO D-Sander units, mud cleaners (Mongoose series)
Replacement Compatibility9621280; verify body cone and feed connection before order

Key Specifications (12" Desander Cone 9621280 Compatible)

ParameterValue
Cone diameter12 in (305 mm)
Inlet / outlet connectionGrooved-end interface, matches M-I SWACO D-Sander header
Flow capacity per cone500 GPM at 45 PSI
Separation range40–100 μm (coarse sand removal)
Cone body materialPolyurethane
Body cone96-21-173 (replaceable internal body)
Feed section96-21-281 (replaceable feed section)
Operating pressureVerify against your D-Sander manifold pressure
Coupling typeGrooved-end coupling

Data source: Technical data table.

Dimensions

DimensionValue
Overall assembly heightMatches 9621280 outline
Cone body OD12 in (305 mm) nominal
Manifold interfaceGrooved-end coupling; existing D-Sander manifold accepts the replacement without bracket modification
Weight (approx.)25–30 kg depending on body configuration

Structure / Working Principle

Drilling mud enters the 12" cone tangentially under pressure. Centrifugal force drives denser sand particles toward the cone wall and down through the apex as underflow, while clarified fluid exits upward through the vortex finder. The larger 12" diameter allows the cone to handle higher flow rates (500 GPM) compared to 4" desilters, making it the primary sand-removal stage.

The cone features replaceable internal sections. If the feed section (96-21-281) or the main body cone (96-21-173) wears out, you can replace just that section without discarding the entire 9621280 assembly. This modular design lowers long-term maintenance costs, especially when the cone operates continuously in high-sand formations.

Cross-Reference & Replacement

Looking for a compatible replacement for an M-I SWACO 9621280? Here's what to check:

  1. Inlet/outlet flange dimensions — confirm against your existing 9621280 cone drawing; the replacement matches the standard 12" M-I SWACO D-Sander interface.
  2. Apex size — standard vs. variable apex; match your current underflow density target.
  3. Coupling type — Grooved-end. Verify the clamp groove on your manifold before ordering.
  4. Internal Components — If you only need the body cone (96-21-173) or feed section (96-21-281), confirm these can be separated from your existing assembly without damage.

Not interchangeable with: 4" twin desilter cones or 12" cones from non-M-I SWACO manifold patterns without dimension verification.

Compatible Host Models

This 12" desander cone is intended for use in:

  • M-I SWACO D-Sander units with 12" cone manifolds
  • Mongoose series mud cleaners with a desander stage
  • M-I SWACO-style systems where 9621280 cone assemblies are specified

For the full M-I SWACO-compatible hydrocyclone range, see M-I SWACO-compatible hydrocyclones — covering both 12" desander and 4" twin desilter sizes.

Applications

  • Primary sand removal — removes sand-sized solids ahead of the desilter stage to protect downstream equipment.
  • Mud cleaner desander section — replaces worn 12" cones on D-Sander-style units during scheduled maintenance shutdowns.
  • High-flow drilling operations — each cone handles 500 GPM at 45 PSI; three-cone manifolds are rated up to 1,500 GPM.
  • Year-end shutdown planning — keep spare body cones on hand to avoid non-productive time when a cone's cut point drifts.

Selection Support

Not sure whether your existing manifold takes a standard or variable apex, or whether you need the complete 9621280 assembly or just the internal body cone (96-21-173)? Send us your current cone drawing or the part number stamped on the cone body, and our team will confirm the matching replacement configuration before you order.

Spare Parts

HYRIG provides replacement parts for the 12" desander cone assembly. The following part-level items can be quoted separately:

Part NameReference Part No.Notes
12" Desander Cone Assembly9621280Complete assembly
Body Cone 12"96-21-173Replaceable internal body
Feed 12"96-21-281Replaceable feed section
ApexVerify against drawingStandard or variable

Qty as per parts list; verify against original drawing. For individual wear parts and inspection guidelines, view our M-I SWACO 12" desander wear parts index.

Frequently Asked Questions

Q1: Is this an original M-I SWACO product?
A: No. HYRIG supplies independent, compatible replacement products and is not affiliated with, authorized by, or endorsed by M-I SWACO or Schlumberger.

Q2: How do I confirm this cone replaces my 9621280?
A: Match the 12" cone diameter and grooved-end coupling. Send us a photo of your existing cone nameplate if the part number is worn.

Q3: What is the typical lead time for a replacement 12" desander cone?
A: Standard polyurethane cones ship in 2–3 weeks. Plan around year-end shutdown windows to avoid downtime.

Q4: Can I order the internal body cone (96-21-173) separately?
A: Yes. The 96-21-173 body cone and 96-21-281 feed section are available as separate wear components. Confirm the fit before ordering.

Q5: What should I inspect if the cone cut point starts drifting?
A: Check the apex opening for erosion and the lower cone section for grooving. A worn apex is the most common cause of coarse underflow.

Contact

For 12" desander cone selection and compatible replacement parts, contact HYRIG: info@hyrig.com

What to include for fastest quote:

  • Existing cone part number or nameplate photo
  • Required quantity
  • Apex size
  • Destination port
Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit