4" Twin Desilter Cone | SWACO 9622220 / 9622221 Compatible

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
This 4-inch twin desilter cone is a drop-in compatible replacement for the M-I SWACO 9622220 assembly and its 9622221 single-cone feed liner. Each twin assembly contains two 4" polyurethane hydrocyclones with a combined feed rate of 150 GPM at 45 PSI, removing solids in the 20–40 μm range. The assembly matches the footprint and manifold interface of standard Mongoose PT mud cleaner and D-Silter configurations, so existing brackets and pipework require no alteration. HYRIG supplies independent, compatible replacement products for M-I SWACO desilter installations; we are not affiliated with, authorized by, or endorsed by M-I SWACO or Schlumberger.
Conatct For Details
DetailReview(0)Additional

Key Facts



Replacement Part No.M-I SWACO 9622220 (twin assembly) / 9622221 (feed liner)
ConfigurationTwo 4" polyurethane hydrocyclones in a single twin body
Flow Capacity150 GPM per twin assembly at 45 PSI
Separation Range20–40 μm (API RP 13C tested)
Apex Size1/2" standard; 3/8" (9622338) and 5/8" (9622358) available
Max Pressure0.35 MPa (50 psi)
Operating Temperature-40°C to +120°C
Compatible HostMongoose PT mud cleaner, D-Silter configurations

Key Specifications (4" Twin Desilter Cone 9622220 / 9622221 Compatible)

ParameterValue
Hydrocyclone size4 in (102 mm) nominal per cone; twin configuration
ConstructionOil-resistant polyurethane (Shore Hardness 85A–90A; ASTM D2000 M2AA 705)
Combined feed rate150 GPM at 45 PSI (reference mud weight 9.5 ppg)
Separation range20–40 μm (API RP 13C tested)
Apex options1/2" standard; 3/8" (9622338) and 5/8" (9622358) optional
Feed liner (single cone)9622221 (urethane)
Max working pressure0.35 MPa (50 psi)
Operating temperature-40°C to +120°C (-40°F to +250°F)
Associated elbow90° polyurethane elbow, 2" grooved end (9622582)

Data source: Technical data table.

Dimensions

DimensionValue
Overall twin assembly footprintMatches 9622220 manifold interface
Individual cone diameter4 in (102 mm) nominal
Manifold connectionGrooved-end coupling, matches Mongoose PT D-Silter header
Weight per 9622221 cone6.8 kg
Associated elbow90° polyurethane, 2" grooved end (9622582)

Structure / Working Principle

Drilling mud enters the twin body through a common feed inlet and splits into two tangential 4" cone inlets. Centrifugal force drives silt-sized solids to the polyurethane wall and down through each cone’s apex as underflow, while clarified fluid exits upward through the vortex finder. The twin design provides 50% greater capacity than a single 4" cone at the same footprint, which is why it is standard on Mongoose PT mud cleaners handling high desilter loads.

Each cone has a replaceable feed liner (9622221) and a replaceable apex. The apex can be changed between 1/2" (standard), 3/8" (9622338), and 5/8" (9622358) without replacing the entire twin assembly. When the polyurethane cone body itself is still within tolerance, you only replace the feed liner or apex—keeping wear-part cost proportional to actual wear, not to the full assembly footprint.

Cross-Reference & Replacement

Looking for a compatible replacement for a 9622220 twin assembly or a 9622221 feed liner? Check these 4 points before ordering:

  1. Assembly vs. component — confirm whether you need the complete twin assembly (9622220) or only the feed liner (9622221) for an existing body. The liner is the 9622221 reference; the complete assembly carries the 1/2" apex by default.
  2. Apex size — standard 1/2" vs. 3/8" (9622338) or 5/8" (9622358). Match your current underflow density target; the apex controls the underflow opening and cut-point coarseness.
  3. Elbow and coupling — the twin assembly connects to the Mongoose PT header via a grooved-end interface. If your existing 90° elbow (9622582) is worn or missing, order it with the cone to avoid a second shutdown.
  4. Manifold feed pressure — verify that your D-Silter feed pump delivers 45 PSI at the manifold. The 150 GPM rating assumes 45 PSI feed pressure and 9.5 ppg reference mud weight; lower pressure reduces throughput, higher pressure accelerates wear.

Not interchangeable with: 12" desander cones (9621280) or 4" cones designed for non-grooved flange manifolds, without verifying the header connection and inlet dimensions first. If your manifold uses a flanged rather than grooved connection, send us the header drawing before ordering.

Compatible Host Models

This 4" twin desilter cone is intended for:

  • Mongoose PT mud cleaner desilter sections (D-Silter configurations)
  • M-I SWACO D-Silter standalone units using 9622220 / 9622221 twin cone assemblies
  • Mud cleaner packages where the 9622220 twin cone is the specified desilter stage

For the 12" desander counterpart used ahead of the desilter stage, see 12" desander cone 9621280 compatible replacement. For the full M-I SWACO-compatible hydrocyclone range, see M-I SWACO-compatible hydrocyclones.

Applications

  • Mongoose PT mud cleaner desilter stage — the twin 4" configuration handles 150 GPM at 45 PSI, removing 20–40 μm solids after the shaker and desander stages.
  • Weighted mud systems — the 1/2" standard apex balances fine-solids removal against barite loss; switch to 3/8" (9622338) for a finer cut or 5/8" (9622358) for higher throughput.
  • HDD and compact mud recycling — the twin 4" footprint provides desilter capacity in a smaller manifold envelope than two separate 4" cones.
  • Scheduled cone or liner replacement during shutdowns — replacing only the 9622221 feed liner or a worn apex extends the service interval of the 9622220 body without full-assembly cost.

Selection Support

Not sure whether your existing unit needs the complete 9622220 twin assembly or just the 9622221 feed liner? Send us a photo of the cone body and the part number stamped on the liner or apex, and we will confirm the matching configuration and apex size before you order.

Spare Parts

HYRIG provides replacement wear components for the 4" twin desilter cone. The following part-level items can be quoted separately against the 9622220 / 9622221 assembly:

Part NameReference Part No.Notes
Clone Twin 4" Urethane Complete w/ 1/2" Apex9622220Complete twin assembly
Feed Liner, Urethane, Twin Cone9622221Single-cone feed liner
Valve Apex 3/8"9622338Optional finer cut
Valve Apex 5/8"9622358Optional higher throughput
Elbow, Grooved End, 90° Polyurethane9622582Manifold elbow

Qty as per parts list; verify against original drawing. For wear-part inspection guidance and the full M-I SWACO-compatible parts index, see M-I SWACO hydrocyclone wear parts.

Frequently Asked Questions

Q1: Is this an original M-I SWACO product?
A: No. HYRIG supplies independent, compatible replacement products and is not affiliated with, authorized by, or endorsed by M-I SWACO or Schlumberger.

Q2: How do I confirm whether I need 9622220 or 9622221?
A: 9622220 is the complete twin assembly; 9622221 is the single-cone feed liner. Match the part number on your existing component before ordering.

Q3: Can I change the apex size without replacing the full twin assembly?
A: Yes. The 3/8" (9622338) and 5/8" (9622358) apexes fit the standard 9622220 body. Confirm the current apex size before switching.

Q4: What is the typical lead time for a 4" twin desilter cone?
A: Standard polyurethane twin assemblies ship in 2–3 weeks. Plan orders ahead of year-end shutdowns to avoid desilter downtime.

Q5: What should I inspect if the twin assembly stops holding cut point?
A: Check the feed liner (9622221) for erosion and the apex opening for enlargement. A worn liner or oversized apex is the most common cause of coarse underflow.

Contact

For 4" twin desilter cone selection and compatible replacement parts, contact HYRIG: info@hyrig.com

What to include for fastest quote:

  • Existing part number (9622220 assembly or 9622221 liner) or a photo of the component
  • Apex size (1/2" standard, 3/8" or 5/8")
  • Required quantity
  • Destination port
Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit