SWACO 4" Twin Cone Parts | 9622220 & 9622221 Wear Parts

2026-11-07 21:24

Key Facts



Primary Wear PartsFeed Liner (9622221), Apex (1/2" std, 9622338, 9622358)
Secondary Wear Parts90° Elbow (9622582)
Compatible Cones4" Twin Desilter (9622220)
MaterialPolyurethane (Shore 85A–90A)
Inspection CycleEvery 500–1,000 operating hours (typical)
Replacement TriggerCoarse underflow spray or cut-point drift

Wear Parts by Configuration

4-inch Twin Desilter Cone (9622220 Compatible)

Part NameReference Part No.Function
Feed Liner, Urethane, Twin Cone9622221Directs mud into the cone; most common wear point
Valve Apex 3/8"9622338Finer cut, used when tighter separation is needed
Valve Apex 5/8"9622358Higher throughput, used when capacity is prioritized
Elbow, Grooved End, 90° Polyurethane9622582Routes overflow; inspect for internal abrasion

Data source: Technical data and parts list.

Wear Inspection Guidance (Symptoms & Actions)

A hydrocyclone's cut point drifts when the apex or feed liner erodes. Instead of guessing a replacement date, monitor the underflow pattern.

  • Normal Operation: The underflow should discharge in a tight, cone-shaped spray (about 20–30°).
  • Worn Apex/Tip: The spray becomes coarse or rope-like. This means the opening has enlarged, letting finer solids bypass to the overflow.
  • Worn Feed Liner: Look for visible grooves or material loss on the inside of the 9622221 liner. Severe erosion changes the inlet angle and disrupts the centrifugal pattern.
  • Action: Shut off the individual cone's feed valve, remove the apex/liner, and inspect. Replace the 9622338 or 9622358 apex if the opening exceeds tolerance. Replace the 9622221 liner if grooving is visible.

Maintenance Tip: Inspect wear parts every 500–1,000 operating hours. In high-sand formations, check more frequently during year-end shutdowns to avoid unplanned downtime.

Cross-Reference & Replacement

Upgrading a worn wear part? Here's how to ensure a drop-in fit:

  1. Confirm the Cone Size: The 4" twin cone uses the 9622221 feed liner and the 1/2" (standard), 3/8" (9622338), or 5/8" (9622358) apex.
  2. Verify Threads and Grooves: Check that the elbow (9622582) is not cross-threaded or stripped before installing the new wear part.
  3. Select Material: Standard polyurethane suits most water-based and oil-based muds. For high-abrasive sand, consider a ceramic option if available.

Not interchangeable with: Apexes or tips designed for non-M-I SWACO manifold patterns or single-cone (non-twin) bodies without verifying thread diameter and pitch.

Compatible Host Models

These wear parts are compatible with:

  • M-I SWACO Mongoose PT mud cleaner desilter sections
  • M-I SWACO D-Silter standalone units using 9622220 twin cone assemblies

To select a complete cone assembly, view the 4" twin desilter cone 9622220 compatible replacement. For the full range overview, see M-I SWACO-compatible hydrocyclones.

Selection Support

Not sure whether your cone uses a standard 1/2" apex or a 3/8" / 5/8" option, or whether the threads on your holder are still serviceable? Send us a photo of the current wear part and the cone body, and we will confirm the exact replacement part number before you order.

Frequently Asked Questions

Q1: Are these original M-I SWACO replacement parts?
A: No. HYRIG supplies independent, compatible wear parts and is not affiliated with or endorsed by M-I SWACO or Schlumberger.

Q2: How do I know when to replace the apex or feed liner?
A: Replace when the underflow spray becomes coarse or rope-like, usually after 500–1,000 operating hours.

Q3: Can I change from a 1/2" to a 3/8" or 5/8" apex?
A: Yes. The 9622338 (3/8") and 9622358 (5/8") apexes fit the standard 9622220 twin assembly.

Q4: What is the lead time for a replacement feed liner or apex?
A: Standard polyurethane wear parts ship in 1–2 weeks. Order before year-end shutdowns to avoid rig downtime.

Contact

For M-I SWACO-compatible hydrocyclone wear parts selection, contact HYRIG: info@hyrig.com

What to include for fastest quote:

  • Current part number or a photo of the worn part
  • Apex size preference (1/2", 3/8", 5/8")
  • Required quantity
  • Destination port
Name:
Message:
Verification code:
Submit
Comment