10" CTX Desander Cone | Brandt 106-200 Compatible Replacement

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
This 10-inch CTX desander cone is a drop-in compatible replacement for the Brandt 106-200 assembly, rated at 400–500 GPM per cone. It is used in primary solids control to remove sand-sized particles in the 90–120 μm range ahead of the desilter stage. The modular 106-200 assembly features replaceable middle and bottom sections (106-208 / 106-201), matching the original installation dimensions for King Cobra, VSM 300, and 3-cone DSN-3H-10CTX headers. HYRIG supplies independent, compatible replacement products for NOV Brandt desander installations; we are not affiliated with, authorized by, or endorsed by NOV Brandt or National Oilwell Varco.
Conatct For Details
DetailReview(0)Additional

Key Facts



Cone Size10 inches
Replacement Part No.Brandt 106-200
Flow Capacity400–500 GPM per cone
Separation Range90–120 μm (mud) / 50–70 μm (water reference)
Apex Size106-204:4AP (1.25" standard)
Cone MaterialUrethane standard; ceramic sections optional
Compatible HostKing Cobra / VSM 300 mud cleaners, DSN-3H-10CTX header
Replacement Compatibility106-200; verify middle/bottom sections and adjusting nut before order

Key Specifications (10" CTX Desander Cone 106-200 Compatible)

ParameterValue
Cone diameter10 in (254 mm)
Inlet / outlet connectionGrooved-end (GxG) interface
Flow capacity per cone400–500 GPM
Separation range (mud)90–120 μm
D50 cut point (water)50–70 μm (for reference only)
Cone body materialUrethane standard; ceramic bottom section available
Internal sectionsMiddle section 106-208; bottom section 106-201:4AP
Underflow controlAdjusting nut 106-205; apex 106-204:4AP
Fluid splitter106-207 (if applicable to header configuration)
Coupling typeGrooved-end (GxG)

Data source: Technical data table.

Dimensions

DimensionValue
Overall assembly heightMatches 106-200 outline
Cone body OD10 in (254 mm) nominal
Manifold interfaceGrooved-end (GxG); existing DSN-3H-10CTX or King Cobra header accepts the replacement without bracket modification
Weight (approx.)15–20 kg depending on ceramic vs. urethane configuration

Structure / Working Principle

Drilling mud enters the 10" CTX cone tangentially under pressure through the grooved-end inlet. Centrifugal force drives denser sand particles toward the cone wall and down through the apex (underflow), while clarified fluid exits upward through the vortex finder. The larger 10" diameter allows the cone to handle higher flow rates (400–500 GPM) compared to 4" desilters, making it the primary sand-removal stage.

The 106-200 assembly is designed with modular internal sections. If the lower cone wears out, you can replace the bottom section (106-201) or the middle section (106-208) independently. The underflow opening is controlled by an adjustable nut (106-205) and a replaceable apex (106-204). This modular design lowers long-term maintenance costs compared to replacing the entire 106-200 assembly when only one section is worn.

Cross-Reference & Replacement

Looking for a compatible replacement for a Brandt 106-200 desander cone? Check these 4 points before ordering:

  1. Modular sections — verify whether you need the complete 106-200 assembly, or only the middle section (106-208) or bottom section (106-201:4AP) for an existing body.
  2. Apex and nut — standard apex is 106-204:4AP (1.25"). Confirm the adjusting nut (106-205) threads and the current apex size before matching.
  3. Fluid splitter — some 10" CTX header configurations use a fluid splitter (106-207). Confirm if your header requires this internal component.
  4. Header coupling — the 10" CTX cone uses a grooved-end (GxG) connection. Verify the clamp groove on your DSN-3H-10CTX or King Cobra manifold before ordering.

Not interchangeable with: 4" CTX desilter cones (26AW / 406-218-U) or 10" cones from non-Brandt manifold patterns without dimension verification.

Compatible Host Models

This 10" CTX desander cone is intended for use in:

  • Brandt King Cobra and King Cobra Hybrid mud cleaner desander sections
  • Brandt VSM 300 mud cleaners with 10" desander cones
  • Brandt DSN-3H-10CTX 3-cone headers and standalone desander units

For the 4" CTX desilter counterpart used after the desander stage, see 4" CTX desilter cone 26AW compatible replacement. For the full NOV Brandt-compatible hydrocyclone range, see NOV Brandt-compatible hydrocyclones.

Applications

  • Primary sand removal on King Cobra / VSM 300 — removes 90–120 μm solids ahead of the desilter stage to protect downstream equipment.
  • DSN-3H-10CTX header configurations — three 10" cones provide 1,200–1,500 GPM total capacity for high-flow mud systems.
  • High-abrasive formations — ceramic bottom sections (106-201) extend service life when standard urethane erodes too quickly.
  • Scheduled section replacement during shutdowns — replacing only the 106-208 middle section or 106-201 bottom section avoids the cost of a complete 106-200 assembly.

Selection Support

Not sure whether you need the complete 106-200 assembly or just the middle section (106-208) or bottom section (106-201)? Send us your current cone drawing or the part number stamped on the cone body, and our team will confirm the matching replacement configuration before you order.

Spare Parts

HYRIG provides replacement parts for the 10" CTX desander cone assembly. The following part-level items can be quoted separately:

Part NameReference Part No.Notes
10" CTX Cone, Complete106-200Complete assembly
Cone Middle Section106-208Replaceable internal section
Cone Bottom Section106-201:4APReplaceable internal section
Apex, 1.25"106-204:4APStandard apex
Nut, Adjusting106-205Underflow control
Fluid Splitter106-207For specific header configurations

Qty as per parts list; verify against original drawing. For individual wear parts and inspection guidelines, view our Brandt CTX hydrocyclone wear parts index.

Frequently Asked Questions

Q1: Is this an original NOV Brandt product?
A: No. HYRIG supplies independent, compatible replacement products and is not affiliated with, authorized by, or endorsed by NOV Brandt or National Oilwell Varco.

Q2: How do I confirm this cone replaces my 106-200?
A: Match the 10" cone diameter, grooved-end coupling, and 1.25" apex (106-204:4AP). Send us a photo of your existing cone nameplate if the part number is worn.

Q3: Can I order just the middle or bottom section?
A: Yes. The 106-208 middle section and 106-201:4AP bottom section are available as separate wear components. Confirm the fit before ordering.

Q4: What is the typical lead time for a replacement 10" CTX cone?
A: Standard urethane cones ship in 2–3 weeks. Ceramic bottom sections may take 4–5 weeks. Plan around year-end shutdown windows.

Q5: What should I inspect if the cone cut point starts drifting?
A: Check the 106-204 apex opening for erosion and the 106-201 bottom section for grooving. A worn apex is the most common cause of coarse underflow.

Contact

For 10" CTX desander cone selection and compatible replacement parts, contact HYRIG: info@hyrig.com

What to include for fastest quote:

  • Existing cone part number or nameplate photo
  • Required quantity
  • Apex size or section needed (106-208 / 106-201)
  • Destination port
Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit