API 609 Triple Offset Butterfly Valve | Wafer & Flanged, Class 150-300

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
HYRIG can supply the API 609 triple offset butterfly valve range. The triple offset geometry removes sliding contact between the disc seal and body seat during rotation, so the seal engages only at
Conatct For Details
DetailReview(0)Additional

API 609 Triple Offset Butterfly Valve

HYRIG can supply the API 609 triple offset butterfly valve range. The triple offset geometry removes sliding contact between the disc seal and body seat during rotation, so the seal engages only at the final closing point. It is metal-seated and torque-seated, available in Class 150 and 300, with wafer and flanged body options.

Key Facts

  • Design standard: API 609, ASME B16.34
  • Pressure class: Class 150 / 300
  • Size range: NPS 2-48 (wafer), NPS 2-40 (flanged)
  • Sealing geometry: Triple offset (three separate offsets)
  • Seat type: Metal-to-metal, torque-seated
  • Body options: Wafer (between flanges), flanged (short pattern)
  • Testing: API 598

Key Specifications

NPSDNWafer L (mm)Wafer Weight (kg)Flanged L (mm)Flanged Weight (kg)
250431410821
4100542012728
6150573114050
8200644515275
1230081105178155
16400102150216230

Data source: Technical data table.

Dimensions

DimensionStandard
Face-to-face (wafer)API 609 Category B
Face-to-face (flanged, short pattern)API 609
Mating flangeASME B16.5 / B16.47
Pressure-temperature ratingASME B16.34

Structure and Working Principle

The triple offset geometry uses three separate offsets. The first offset places the shaft behind the sealing surface centerline; the second offsets the shaft from the bore centerline; the third offsets the seat cone axis from the shaft. The combined effect is that the disc lifts clear of the seat almost immediately on opening and contacts the seat only at the final degree of closing. There is no sliding friction across the sealing surfaces during travel.

Because the seal is metal-to-metal and engaged by torque rather than by soft-seat interference, the valve can be used at temperatures and pressures where PTFE or RPTFE seats would deform or fail. This is also the structural basis for fire-safe performance: the metal seat remains after any soft secondary components are consumed.

Cross-Reference and Replacement

Replacing a double-offset or soft-seated butterfly valve with a triple-offset design requires verification of four factors:

  1. Temperature boundary: A soft-seated double-offset valve is typically limited to about 204 C. Confirm whether the line temperature requires a metal-seated triple-offset valve.
  2. Body style: Wafer and flanged triple-offset bodies have different face-to-face dimensions and pressure-rating ownership. Confirm the piping gap and whether the mating flanges can compress a wafer body.
  3. Torque and actuator: Triple-offset valves are torque-seated. Confirm the actuator output matches the required seating torque, not the running torque.
  4. RFQ clarity: State both "triple offset" (geometry) and "metal seated" (sealing construction). Stating only one leaves the design basis ambiguous.

Applications

  • High-temperature steam isolation: Metal seat and torque seating remain functional above soft-seat temperature limits.
  • Fire-safe hydrocarbon isolation: Inherent metal seat geometry supports API 607 fire-safe performance.
  • Space-constrained skids: Wafer triple-offset body adds minimal face-to-face length.
  • Frequent cycling with tight shutoff: Low-friction opening and final-contact sealing reduce seat wear over cycle life.

Disclaimer: This equipment is designed for high-pressure industrial applications. Ensure strict compliance with local safety standards and verify pressure ratings prior to installation.

Frequently Asked Questions

Q: At what temperature does a double-offset butterfly valve fail?

The soft seat typically limits double-offset valves to about 204 C. Above that, a triple-offset metal seat is required.

Q: Does a triple-offset valve rub the seat during opening?

No. The third offset produces a camming action that lifts the disc clear of the seat at the start of opening. Contact occurs only at the final closing point.

Q: What is the difference between wafer and flanged triple-offset bodies?

A wafer body is compressed between mating flanges and has a very short face-to-face. A flanged body has its own flanged ends and a longer face-to-face. The pressure rating of a wafer body belongs to the bolted flange assembly.

Q: What is the typical lead time?

Standard lead time is 4-6 weeks depending on size, class, body style, and actuation.

Selection Support

To confirm the correct body style, seat construction, and actuator torque for your line, provide the line size, pressure class, temperature, medium, and available face-to-face gap. Our engineering team will verify the triple-offset geometry and torque requirement against API 609.

Contact

For API 609 triple offset butterfly valve selection, contact HYRIG: info@hyrig.com

Related Pages

Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit