API 594 Wafer Check Valve | Single & Dual Plate, Type A

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
HYRIG can supply the API 594 wafer check valve range. The wafer check valve is a non-return valve that fits compressed between two pipe flanges, with no ends of its own.
Conatct For Details
DetailReview(0)Additional

API 594 Wafer Check Valve

HYRIG can supply the API 594 wafer check valve range. The wafer check valve is a non-return valve that fits compressed between two pipe flanges, with no ends of its own. It is available in single-plate and dual-plate designs, Class 150 and 300, in API 594 Type A short face-to-face dimensions.

Key Facts

  • Design standard: API 594, API 6D
  • Face-to-face category: API 594 Type A (short pattern)
  • Pressure class of assembly: Class 150 / 300
  • Size range: NPS 2-48
  • Plate design: Single plate / dual plate (spring-assisted)
  • Body materials: ASTM A216 WCB, A351 CF8, A351 CF8M
  • End connections: Wafer (between flanges), RF or RTJ mating
  • Testing: API 598

Key Specifications

NPSDNL (mm)D (mm)D2 (mm)D3 (mm)Weight (kg)
2506010351562
3807313580884
4100731731021086
61509822015216013
820012727720321025
1025014633725426639
1230018140730531054

Data source: Technical data table.

Dimensions

DimensionStandard
Face-to-face (Type A)API 594
Mating flange drillingASME B16.5 / B16.47
Pressure-temperature ratingASME B16.34 (flange assembly)
TestingAPI 598

Structure and Working Principle

The wafer check valve has a body that fits between two flanges. Forward flow opens the plate or plates; reverse flow or spring force closes them against the seat. Because the valve has no flanged ends, the pressure rating belongs to the bolted flange assembly, not to the loose valve body.

The single-plate design uses one disc that swings or lifts off the seat. It is compact and works in any orientation with spring assistance. The dual-plate design uses two D-shaped half-plates on a central hinge pin, each with its own spring. The shorter plate travel gives faster closure and lower water hammer risk, which is why dual-plate wafer checks are common on pump discharge with frequent stops.

Cross-Reference and Replacement

Replacing a flanged swing check with a wafer check requires verification of four factors:

  1. Face-to-face category: API 594 Type A is not dimensionally interchangeable with a flanged swing check (Type B or ASME B16.10 long pattern). Confirm the piping gap.
  2. Flange bore and gasket ID: The gasket must not protrude into the valve bore or obstruct plate movement.
  3. Installation orientation: Single-plate and dual-plate designs accept horizontal or vertical upward flow. Downward-flow vertical installation is not acceptable.
  4. Pressure rating ownership: The Class 150 or 300 rating applies to the bolted flange assembly, not to the loose valve body.

Applications

  • Pump discharge with frequent stops: Dual-plate design closes quickly and reduces water hammer compared with a swing check.
  • Low-pressure gas and minimum-flow service: Spring-assisted plates seal without relying on reverse flow to center the disc.
  • Space-constrained skids and manifolds: API 594 Type A face-to-face is a fraction of a flanged swing check length.
  • Vertical upward flow: Spring-assisted designs can be installed in vertical lines, subject to cracking pressure confirmation.

Disclaimer: This equipment is designed for high-pressure industrial applications. Ensure strict compliance with local safety standards and verify pressure ratings prior to installation. The gasket inside diameter must not obstruct plate movement; verify flange centering and clearance before bolting.

Frequently Asked Questions

Q: What is the difference between API 594 Type A and Type B?

Type A is short face-to-face (wafer or lug). Type B is long face-to-face, dimensionally equivalent to a flanged swing check. They are not interchangeable.

Q: Does a wafer check valve have its own pressure rating?

No. The pressure class belongs to the bolted flange assembly. The valve body seals compressed between the mating flanges.

Q: What is the difference between single-plate and dual-plate wafer check valves?

A single plate uses one disc with a longer travel. A dual-plate design uses two spring-loaded half-plates with shorter travel, giving faster closure and lower water hammer risk.

Q: Can a wafer check valve be installed vertically?

Yes, with upward flow. Downward-flow vertical installation is not acceptable.

Q: What is the typical lead time?

Standard lead time is 4-6 weeks depending on size, class, material, and plate design.

Selection Support

To confirm the correct plate design, face-to-face category, and spring for your line, provide the line size, flange class, medium, flow direction, and whether water hammer or low-pressure opening is a concern. Our engineering team will verify the API 594 Type A dimensions and installation clearance.

Contact

For API 594 wafer check valve selection, contact HYRIG: info@hyrig.com

Related Pages

Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit