HYRIG can supply the API Y pattern strainer range. The Y-strainer is a compact pipeline protector with an angled screen chamber that captures debris before it reaches pumps, valves, steam traps, and meters. It is available in Class 150, 300, and 600, with mesh sizes from 5 to 300 and stainless steel screens.
| NPS | DN | L RF (mm) | H (mm) | H1 (mm) | Weight (kg) |
|---|---|---|---|---|---|
| 1/2 | 15 | 108 | 67 | 92 | 2 |
| 1 | 25 | 127 | 87 | 117 | 3 |
| 2 | 50 | 203 | 145 | 185 | 13 |
| 3 | 80 | 241 | 190 | 250 | 18 |
| 4 | 100 | 292 | 245 | 340 | 22 |
| 6 | 150 | 406 | 325 | 450 | 50 |
| 8 | 200 | 495 | 370 | 500 | 91 |
| 12 | 300 | 699 | 525 | 735 | 297 |
Data source: Technical data table.
| Mesh | Wire Dia A (SWG) | Opening B (mm) | Open Area D (%) |
|---|---|---|---|
| 20 | 28 | 0.356 | 45.7 |
| 40 | 36 | 0.193 | 43.6 |
| 60 | 38 | 0.152 | 41.0 |
| 100 | 42 | 0.102 | 35.8 |
| 200 | 47 | 0.051 | 35.9 |
| 300 | 48 | 0.039 | 27.6 |
Data source: Technical data table.
| Dimension | Standard |
|---|---|
| Face-to-face | ASME B16.10 |
| Flanged ends | ASME B16.5 |
| Butt weld ends | ASME B16.25 |
| Pressure-temperature rating | ASME B16.34 |
The flow enters the angled screen chamber, passes through the stainless steel screen, and exits through the outlet. Debris larger than the screen opening is captured on the inside of the screen. The angled chamber allows gravity to collect debris at the bottom, away from the flow path.
The Y-strainer is compact and can be installed in horizontal or vertical lines with the screen chamber pointing downward. It is a permanent pipeline component, not a temporary startup device; the screen is cleaned by removing the bonnet or, if equipped, by opening a blowdown valve at the drain port.
Replacing or specifying a Y-strainer requires verification of four factors:
Disclaimer: This equipment is designed for high-pressure industrial applications. Ensure strict compliance with local safety standards and verify pressure ratings prior to installation. Blowdown operations must be performed with appropriate isolation and personal protective equipment.
Q: What mesh size do I need for a steam trap?
20-40 mesh (0.40-0.85 mm) is standard for steam trap protection. Finer mesh blinds faster and may not be necessary.
Q: Does a Y-strainer need a blowdown valve?
A blowdown valve is recommended for dirty fluids and sizes above NPS 2 1/2. Clean gas and small lines can be cleaned manually by removing the screen.
Q: What is the difference between 40 mesh and 100 mesh?
40 mesh has an opening of about 420 micron; 100 mesh is about 149 micron. The finer screen captures smaller particles but blinds faster.
Q: Can a Y-strainer be installed vertically?
Yes, with the screen chamber pointing downward. Upward-flow vertical installation with the chamber pointing up is not recommended.
Q: What is the typical lead time?
Standard lead time is 4-6 weeks depending on size, class, material, and mesh requirement.
To confirm the correct Y-strainer size, mesh, and material for your line, provide the line size, pressure class, medium, downstream equipment, and dirt loading. Our engineering team will verify the screen opening and open area against your filtration requirement.
For API Y-strainer selection, contact HYRIG: info@hyrig.com
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.