Wafer vs Flanged Check Valve | Space, Weight & Maintenance

2026-11-17 15:17

Wafer vs Flanged Check Valve

HYRIG supplies both wafer and flanged check valves. This guide compares the API 594 Type A short face-to-face wafer design against the conventional flanged swing check, covering space, weight, maintenance, and where each type belongs.

Key Facts

  • Wafer: Fits between flanges, short face-to-face, light, lower material cost. Requires precise centering and gasket ID control.
  • Flanged: Has its own flanged ends, long face-to-face, heavier, easier to remove as a standalone unit.
  • Face-to-face: API 594 Type A wafer is not dimensionally interchangeable with a flanged swing check (Type B or ASME B16.10 long pattern).
  • Maintenance: A wafer valve can be removed by spreading the flanges; a flanged valve unbolts as a complete unit.

Key Specifications

FeatureWafer CheckFlanged Swing Check
Face-to-faceAPI 594 Type A shortAPI 594 Type B / ASME B16.10 long
Weight (typical 10")Low (compact body)Higher (full body and flanges)
InstallationBetween two flangesBolted to mating flanges
CenteringCritical: body must be centeredSelf-aligning through flange bolts
Gasket ID controlMust not obstruct plateLess sensitive to gasket ID
RemovalSpread flanges, lift outUnbolt and remove complete valve

Dimensions

DimensionStandard
Wafer face-to-faceAPI 594 Type A
Flanged face-to-faceAPI 594 Type B / ASME B16.10
Mating flangeASME B16.5 / B16.47

Structure and Working Principle

A wafer check valve has no ends of its own. The body is compressed between two pipe flanges, and the seal is made by the gasket and flange faces. Because the body is short, the valve adds very little length to the piping run and weighs a fraction of a flanged swing check of the same size.

A flanged swing check has its own flanged ends and a full body. It is longer and heavier, but it can be removed and replaced as a standalone unit without spreading the adjacent pipe flanges. The flanged body also provides more space around the disc and seat, which can be an advantage in dirty or viscous service.

Cross-Reference and Replacement

When replacing a flanged check with a wafer check:

  1. Check the piping gap: API 594 Type A is much shorter than a flanged swing check. A spacer or spool piece may be required.
  2. Check the gasket ID: The gasket must not protrude into the bore or block plate movement.
  3. Check the maintenance procedure: A wafer valve requires spreading the flanges; confirm the line can be opened enough for removal.

Applications

  • Wafer: Space-constrained skids, pump discharge with dual-plate design, weight-sensitive offshore or modular piping.
  • Flanged: Dirty or viscous service, standalone equipment connections, lines where the valve must be removed without spreading pipe.

Disclaimer: This equipment is designed for high-pressure industrial applications. Ensure strict compliance with local safety standards and verify pressure ratings prior to installation.

Frequently Asked Questions

Q: Is a wafer check valve shorter than a flanged check valve?

Yes. API 594 Type A wafer face-to-face is substantially shorter than a flanged swing check of the same size. Confirm the exact dimensions before designing the piping gap.

Q: Can a wafer check valve replace a flanged check valve directly?

Not without checking the face-to-face length and piping gap. A spacer or spool piece may be needed. The two types are not dimensionally interchangeable.

Q: Which type is easier to maintain?

A flanged check can be unbolted as a complete unit. A wafer check requires spreading the adjacent flanges. The better choice depends on the line layout and maintenance access.

Q: What is the typical lead time?

Standard lead time is 4-6 weeks depending on size, class, material, and design.

Selection Support

To choose between a wafer and flanged check valve, provide the piping layout, available face-to-face gap, maintenance access, and medium. Our engineers will confirm the correct design and dimensions.

Contact

For help selecting between wafer and flanged check valves, contact HYRIG: info@hyrig.com

Related Pages

Name:
Message:
Verification code:
Submit
Comment