API ASME B16.5 RF Flange RFQ Checklist | Bore & Bolting

2026-11-16 18:27

API ASME B16.5 RF Flange RFQ Checklist

HYRIG can supply API ASME B16.5 RF flanges. Because flanges are dimensional boundary components, an incomplete Request for Quotation (RFQ) often leads to mismatched bolt holes, incorrect bore sizes, or improper gasket selection. The RFQ must include specific dimensional and material data.

Key Facts

  • Critical Dimensions: Nominal Pipe Size (NPS), Pressure Class, and Bore Size.
  • Facing: Specify Raised Face (RF) height (1.6 mm for Class 150/300).
  • Bolting: Specify Stud Bolt (L1) or Machine Bolt (L2).
  • Material: Standard is A105 for carbon steel, F304/F316 for stainless.

Key Specifications

To receive a correctly machined flange, provide the following data in your RFQ:

Data FieldWhy It Is Needed
Nominal Pipe Size (NPS)Defines the flange OD, bolt circle, and bolt size.
Pressure ClassDetermines the flange thickness, bolt size, and facing height.
Bore Size (ID)Must match the pipe ID to avoid welding steps or flow restrictions.
Facing TypeSpecify Raised Face (RF) and verify the height (1.6 mm).
Material GradeSpecify ASTM A105, A182 F304, or A182 F316 based on the medium.
Bolting TypeSpecify Stud Bolts (L1) or Machine Bolts (L2) to ensure correct length.
DocumentationState if EN 10204 3.1 material certificates are required.

Dimensions

DimensionStandard
Flange OD (D)ASME B16.5
Bolt Circle (D1)ASME B16.5
RF Diameter (D2)ASME B16.5
Bolt Hole (d)ASME B16.5

Structure and Working Principle

A common error in flange RFQs is specifying the NPS without specifying the bore size. A 4-inch Class 150 flange can be supplied with a standard bore to match Schedule 40, Schedule 80, or a custom bore to match a specific pipe ID.

Another frequent error is mismatching the bolting. If the RFQ does not state whether the joint uses stud bolts or machine bolts, the supplier may quote a bolt length that is too short (if L2 is used instead of L1) or too long, leading to inadequate thread engagement or mechanical interference.

Cross-Reference and Replacement

When ordering replacement flanges:

  1. Measure the Existing Bore: Do not assume the bore matches the standard pipe schedule. Measure the actual ID of the pipe or the existing flange.
  2. Check the Facing: Confirm the existing flange is RF (1.6 mm) and not FF (Flat Face) or RTJ (Ring Type Joint).
  3. Verify Bolt Holes: Ensure the bolt circle and hole diameter match the mating flange to avoid rotational misalignment.

Applications

  • New Piping Construction: Ordering flanges that match the line class and pipe schedule exactly.
  • Maintenance and Repair: Replacing corroded or damaged flanges in existing lines.
  • Equipment Connections: Sizing flanges to match pumps, valves, and vessels.

Disclaimer: This equipment is designed for high-pressure industrial applications. Ensure strict compliance with local safety standards and verify pressure ratings prior to installation.

Frequently Asked Questions

Q: What happens if the flange bore does not match the pipe ID?

A mismatch creates a step at the weld joint. This can cause turbulence, erosion, and may fail radiographic inspection. The flange bore must match the pipe ID.

Q: Do I need to specify the gasket thickness in the RFQ?

It is highly recommended. The gasket thickness affects the bolt length calculation. If a non-standard gasket is used, the required L1 or L2 bolt length will change.

Q: What is the typical lead time for ASME B16.5 flanges?

Standard lead time is 4 to 6 weeks depending on the size, pressure class, and material. Custom bores may require additional time.

Selection Support

To confirm the correct flange dimensions and bolting for your line, provide the NPS, pressure class, pipe schedule, and facing type. Our engineering team will verify the bore and bolting against ASME B16.5.

Contact

For API ASME B16.5 RF flange RFQ support, contact HYRIG: info@hyrig.com

Related Pages

Name:
Message:
Verification code:
Submit
Comment