API RF Flange Class Boundary | Height Limits & RTJ Transition

2026-11-16 18:28

API RF Flange Class Boundary

HYRIG can supply API ASME B16.5 flanges. The raised face (RF) is the standard for Class 150 and 300, but its height and application boundaries change at higher pressure classes. This page explains the dimensional changes and when to transition to Ring Type Joint (RTJ) flanges.

Key Facts

  • Class 150 & 300: RF height is 1.6 mm. This is the standard for carbon and stainless steel flanges.
  • Class 600 & Above: RF height increases to 6.4 mm to accommodate thicker, high-pressure gaskets.
  • Pressure Boundary: RF is typically used up to Class 600. For Class 900 and above, RTJ facings are the industry standard.
  • Interchangeability: A 1.6 mm RF cannot mate with a 6.4 mm RF. They have different gasket seating dimensions.

Key Specifications

FeatureClass 150 / 300Class 600Class 900+
RF Height1.6 mm6.4 mmN/A (RTJ standard)
Gasket TypeSpiral wound, graphiteSpiral wound, high strengthMetal ring joint (RTJ)
Typical FacingRFRF or RTJRTJ
Pressure LimitModerateMedium-HighHigh

Dimensions

DimensionRequirement
RF Height (Class 150/300)1.6 mm
RF Height (Class 600)6.4 mm
RF Height (Class 900+)N/A (RTJ groove)
Facing Finish125–250 AARH

Structure and Working Principle

The raised face height is determined by the pressure class. For Class 150 and 300, a 1.6 mm raised face is sufficient to concentrate the bolt load onto a standard spiral wound gasket.

As the pressure class increases to 600, the flange thickness and bolt size increase. The raised face height also increases to 6.4 mm to accommodate a thicker, higher-strength gasket required to seal the higher pressure.

For Class 900 and above, the bolt loads and pressure are so high that a compressed gasket is no longer reliable. The industry shifts to RTJ flanges, where a metal ring is wedged into a machined groove, providing a highly reliable metal-to-metal seal.

Cross-Reference and Replacement

When replacing flanges across pressure classes:

  1. Verify the RF Height: Do not assume all RF flanges are 1.6 mm. If replacing a Class 600 flange, ensure the replacement is machined to 6.4 mm.
  2. Check the Mating Flange: If the existing system uses a Class 600 flange with a 6.4 mm RF, a standard Class 150 flange (1.6 mm RF) will not seal correctly against it.
  3. Consider RTJ: If upgrading the line to Class 900 or higher, plan to replace the entire joint (both flanges and gasket) with an RTJ system.

Applications

  • Class 150/300 Systems: General process piping, water lines, and low-pressure steam.
  • Class 600 Systems: High-pressure process lines, boiler feedwater, and medium-high pressure gas.
  • Class 900+ Systems: High-pressure gas wells, hydrogen service, and critical offshore pipelines.

Disclaimer: This equipment is designed for high-pressure industrial applications. Ensure strict compliance with local safety standards and verify pressure ratings prior to installation.

Frequently Asked Questions

Q: Can I use a Class 150 RF flange on a Class 300 system?

No. The flange dimensions (OD, bolt circle, thickness) are different. The bolt holes will not align, and the pressure rating will be insufficient.

Q: What is the RF height for Class 600?

The raised face height for Class 600 is 6.4 mm, which is larger than the 1.6 mm used for Class 150 and 300.

Q: Why is RTJ used for Class 900 and above?

RTJ uses a metal ring gasket wedged into a groove. This metal-to-metal seal is far more reliable than a compressed flat gasket under extreme pressure and thermal cycling.

Q: What is the typical lead time?

Standard lead time is 4 to 6 weeks depending on the flange size, class, and material.

Selection Support

To confirm the correct facing and height for your piping class, provide the line pressure and existing flange dimensions. Our engineering team will verify the specification against ASME B16.5.

Contact

For API ASME B16.5 flange selection, contact HYRIG: info@hyrig.com

Related Pages

Name:
Message:
Verification code:
Submit
Comment