This page presents verified field cases of our API 610 BB2 horizontal, radially split, between-bearings pumps operating in critical heavy-duty services. Each case demonstrates the pump's reliability, efficiency, and durability under real industrial conditions.
Case 1 – Refinery Crude Oil Transfer (Middle East Refinery)
Background: A 300,000 bpd refinery needed a reliable crude oil transfer pump to feed the atmospheric distillation unit. Operating conditions: high flow, moderate head, continuous 24/7, outdoor desert environment.
BB2 Pump Solution:
Flow: 1,200 m³/h
Head: 120 m
Temperature: 180°C
Material: Carbon steel casing, 316L impeller
Seal: API 682 Plan 21 mechanical seal
Speed: 1480 rpm
Results:
5 years of continuous operation without major overhaul
Bearing housing vibration consistently below 2.5 mm/s (well within API 610 limits)
Stable performance across crude viscosity variations
Full API 610 compliance documented in quarterly vibration reports
Available references: Site photos, installation drawing, vibration trend logs.
Case 2 – Petrochemical Amine Circulation (Southeast Asia)
Background: A petrochemical plant required a rich amine circulation pump for gas desulfurization. Amine service is challenging due to high temperature, potential foaming, and risk of leakage.
BB2 Pump Solution:
Flow: 850 m³/h
Head: 210 m
Temperature: 120°C
Material: 316L stainless steel (casing, impeller, shaft)
Seal: API 682 Plan 53B dual cartridge mechanical seal
Bearing: Oil mist lubrication
Results:
Zero leakage over 3+ years of operation
Stable desulfurization performance with consistent outlet pressure
No amine degradation or seal failure
Annual inspection shows minimal wear on wear rings and bearings
Available references: P&ID, seal support system diagram, performance test report.
Case 3 – Power Plant Boiler Feed Pump (South Asia)
Background: A 250 MW coal-fired power plant needed a high-efficiency boiler feed pump (intermediate pressure stage) to replace an aging overhung pump that suffered from high vibration and poor efficiency.
BB2 Pump Solution:
Flow: 600 m³/h
Head: 380 m
Temperature: 160°C
Material: Carbon steel casing, 316L impeller
Seal: API 682 Plan 23 (high temperature)
Efficiency: 83% at duty point
Results:
Matched full‑load operation from 50% to 110% of plant capacity
83% efficiency – 5% higher than replaced pump, saving ~150,000 kWh/year
Vibration levels below 2.0 mm/s
Simple maintenance: radial split cover allows internal inspection without removing motor or piping
Available references: Performance curve (as-tested), efficiency comparison chart, maintenance log.
Case 4 – FPSO Seawater Injection (Offshore Brazil)
Background: An FPSO vessel required a large flow seawater injection pump for reservoir pressure maintenance. Seawater service demands superior corrosion resistance and 24/7 reliability in a compact footprint.
BB2 Pump Solution:
Flow: 2,000 m³/h
Head: 150 m
Material: Duplex stainless steel (casing, impeller, shaft)
Seal: API 682 Plan 53B with seawater-compatible faces
Coating: Epoxy for external corrosion protection
Results:
24/7 continuous operation for 2 years (ongoing)
No corrosion, pitting, or erosion despite high chlorides
Double suction design provides low NPSH – critical for seawater lift
Bearing temperature stable at 70–75°C under full load
Available references: Offshore site photos, dimensional drawing, commissioning report, NPSH verification data.
What You Can Request From Us for Each Case
Site photos and installation images
Project parameter sheet (flow, head, power, material, seal plan)
P&ID of pump system (where available)
Actual running data (vibration, bearing temperature, pressure, power consumption)
User reference contact (with prior permission)
Why Real Project Cases Matter
Field references prove that our BB2 pumps deliver:
Long uninterrupted operation (years, not months)
Low vibration and high efficiency in refinery and petrochemical services
Corrosion-free performance in duplex material for seawater and amines
API 610 compliance with documented test results
Get the Complete BB2 Pump Case Study Package
We can match your operating conditions to similar successful installations. Request the BB2 pump project case PDF or ask for references in your specific industry.
Email: info@hyrig.com
Please specify your industry (refinery / petrochemical / power / FPSO / other) and we will send relevant case studies, photographs, and technical data within 24 hours. We also welcome inquiries to arrange a technical discussion with our pump application engineers.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.