HYRIG BB4 Lean Amine High Pressure Booster Pump: API 610 horizontal split (axially split) multistage between-bearing pump for lean amine injection into high pressure absorbers. Flow 100-2000 m³/h, head 300-800 m, temp up to 120°C, design pressure up to 80 bar. Horizontal split casing allows full rot

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
HYRIG BB4 Lean Amine High Pressure Booster Pump: API 610 horizontal split (axially split) multistage between-bearing pump for lean amine injection into high pressure absorbers. Flow 100-2000 m³/h, head 300-800 m, temp up to 120°C, design pressure up to 80 bar. Horizontal split casing allows full rotor access without pipe disconnection. 316L wetted parts, API 682 Plan 53B dual seal, centerline mounted.

Conatct For Details
DetailReview(0)Additional

Product Overview
The HYRIG BB4 Lean Amine High Pressure Booster Pump is a heavy-duty, multi-stage, horizontal split casing (axially split), between-bearing centrifugal pump, fully compliant with API 610 (ISO 13709) standards. Specifically engineered for high head lean amine booster service – pumping regenerated lean amine (MDEA, DEA, MEA) from low pressure regenerator or surge drum directly into high pressure absorbers (typically 50–80 bar) in gas sweetening, refinery tail gas treating, and CO₂ capture units – this pump delivers up to 800 meters of head while accommodating flows up to 2000 m³/h.

The horizontal split casing is a key differentiator: the top half can be lifted off without disturbing suction or discharge piping, providing unobstructed access to the entire rotor, bearings, wear rings, and interstage bushings. For high pressure amine booster pumps that require periodic internal inspection, this feature dramatically simplifies maintenance and reduces downtime.

Key Technical Parameters

  • Pump Type: API 610 BB4 Horizontal Split (Axially Split), Multi‑Stage (4 to 10 stages), Between‑Bearing Centrifugal Pump

  • Flow Range: 100 – 2000 m³/h

  • Head Range: 300 – 800 m (higher with additional stages)

  • Working Temperature: Up to 120°C (lean amine typical 50–90°C)

  • Design Pressure: Up to 80 bar (casing rated for full absorber pressure)

  • Structure: Horizontal split casing (upper and lower halves), centerline mounted, dual heavy duty bearings, rotor accessible with top casing removed

  • Seal Standard: API 682 – Plan 53B (pressurized dual seal) with compatible barrier fluid; Plan 11+62 available for less critical emissions.

  • Materials: 316L stainless steel wetted parts (standard) – impellers, diffusers, wear rings, shaft sleeve; carbon steel casing with 316L trim optional. NACE MR0175 for sour amine service.

  • Application: Lean amine booster pump from regenerator or lean amine surge drum to high pressure absorber (e.g., natural gas sweetening at 60–80 bar, refinery hydrogen plant CO₂ removal, pre‑combustion carbon capture).

Horizontal Split Advantage for High Pressure Amine Booster

FeatureHYRIG BB4 Benefit
Top casing removalAccess rotor, bearings, and internal seals without breaking pipe flanges – saves 50‑70% of maintenance time compared to designs that require piping disassembly
No realignment after maintenanceCasing dowels and precision machined split line ensure repeatable alignment; simply replace top half and torque bolts
Full rotor visibilityInspect all impellers, diffusers, wear rings, and interstage bushings in situ – no need to pull the rotor for routine checks
Ease of seal and bearing replacementMechanical seal and bearings can be replaced with top casing open and rotor still in place – further reduces outage duration

Technical Challenges & Solutions for High Head Lean Amine Booster – BB4

ChallengeHYRIG BB4 Solution
High differential pressure (300–800 m head)Multi-stage (4 to 10 stages) hydraulic design – each stage contributes 70–90 m head, reaching required discharge pressure without series pumps
Low available NPSH at pump suctionFirst stage impeller optimized for low NPSH; optional inducer reduces NPSH3 by up to 40%
Seal leakage at high pressureAPI 682 Plan 53B pressurized dual seal with accumulator – maintains barrier fluid pressure > suction pressure, zero amine emissions
Vibration at high head and speedBetween-bearing short span, large diameter shaft, precision balanced rotor, tilting pad journal bearings – vibration <2.5 mm/s
Corrosion from heat stable salts (HSS) in amine316L stainless steel for all wetted internal components (impellers, diffusers, wear rings, shaft sleeve) – maximum resistance to formate, acetate, and oxalate attack
Long maintenance outagesHorizontal split casing: top half removed in <2 hours, rotor fully exposed. Bearings and seals replaced without rotor extraction – typical turnaround reduced by 60% compared to radial split designs
Continuous high pressure operation (>5 years between overhauls)Hardened stellited wear rings, heavy duty oil mist lubrication, API 610 bearing housing seals – proven MTBR >6 years in similar services

Case Study Snapshot – Offshore Gas Platform, Malaysia

  • Application: Lean MDEA booster pump from regenerator to 75 bar absorber. Flow 750 m³/h, head 640 m (6 stages).

  • HYRIG BB4 solution: Horizontal split casing, 316L wetted parts, Plan 53B seal, oil mist lubrication.

  • Maintenance outcome:

    • Scheduled inspection every 2 years: top casing removed, wear rings measured, seal replaced – total downtime 8 hours (previously design required 24 hours for rotor pull-out).

    • Zero unscheduled outages in 3 years.

    • Vibration <1.8 mm/s.

  • Full case study available upon request.

Key Features for High Head Lean Amine Booster Service – BB4

  • API 610 BB4 Compliance – Designed to the highest industry standard for continuous, high pressure, hazardous service.

  • Multi-Stage High Head – Up to 10 precision machined stages deliver heads to 800 m, meeting the most demanding absorber injection pressures.

  • Horizontal Split Casing – Top half lifts off without disturbing suction/discharge piping. Full access to internal components. Reassembly is repeatable with dowel pins – no realignment required.

  • Centerline Mounted Casing – Maintains rotor alignment during temperature changes (start-up to steady state), preventing internal contact and wear.

  • Low NPSH First Stage – Custom engineered first stage impeller with large inlet eye; inducer option reduces NPSH requirement by 40%, ideal for regenerator bottom or lean amine surge drum with limited elevation.

  • Zero Fugitive Emissions – API 682 Plan 53B dual pressurized mechanical seal with reservoir/accumulator; barrier fluid (water/glycol or synthetic) ensures no amine or VOC release to atmosphere.

  • Corrosion Resistant Metallurgy – Full 316L stainless steel impellers, diffusers, and wear rings standard; Super Duplex available for offshore high chloride amine systems.

  • High Efficiency Multistage Hydraulics – CFD designed diffuser and impeller profiles achieve 84–87% efficiency even at high head, reducing energy consumption over decades of 24/7 operation.

  • Heavy Duty Bearing System – Tilt‑pad or multi‑lobe journal bearings, angular contact thrust bearings, oil mist or forced oil lubrication, and continuous temperature/vibration monitoring.

  • Simplified Rotor Access – With top casing removed, all impellers and diffusers are visible without extracting the rotor. For full rotor removal, the cartridge can be lifted vertically after unbolting the lower casing half – no axial extraction required.

  • Hardfaced Wear Rings – Stellited wear rings on impellers and casing maintain tight clearances over extended service life, preserving hydraulic efficiency.

Typical Applications

  • Lean amine booster to high pressure absorber in natural gas sweetening (onshore and offshore – especially where maintenance access is valued)

  • Refinery tail gas treating unit (TGTU) – lean MDEA injection into high pressure contactor with frequent access for amine system cleaning

  • Pre‑combustion CO₂ capture (hydrogen production from natural gas or coal) – amine circulation to high pressure absorber in plants with scheduled short turnarounds

  • High pressure amine wash in syngas purification (ammonia, methanol plants) – BB4 provides maintenance ease for critical path equipment

  • Biogas upgrading to biomethane using high pressure amine absorption

Why HYRIG BB4 for High Head Lean Amine Booster?

HYRIG BB4 pumps are specifically designed for lean amine high pressure booster service where maintainability is as important as hydraulic performance. The horizontal split casing delivers:

  • Faster, simpler inspections – top casing off in hours

  • No piping disturbance – suction and discharge stays bolted

  • No realignment after maintenance

  • Lower life cycle cost – reduced downtime per maintenance event

Coupled with multistage high head capability, 316L corrosion resistance, and API 682 Plan 53B sealing, the HYRIG BB4 is the ideal choice for high pressure absorber feed in large gas sweetening and carbon capture facilities.

Download Resources

Request the following from our technical team:

  • BB4 Lean Amine High Pressure Booster Pump Selection Guide – head/flow curves for 4/6/8/10 stages

  • API 682 Plan 53B P&ID for High Pressure Amine Service (PDF)

  • Case Study Pack – BB4 installations with maintenance time comparisons

  • 3D CAD model (STEP) for plant integration

  • API 610 Datasheet (Excel template)

Contact: info@hyrig.com – subject line “BB4 Amine High Pressure Inquiry”

Contact Us

For technical quotation, multistage hydraulic selection, or to discuss your high pressure absorber feed requirements and maintenance interval planning, please email us at: info@hyrig.com

Our engineering team will respond within 24 hours with a pump selection optimized for your lean amine flow, absorber pressure, amine type, NPSH, and desired inspection frequency.


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit