This page provides complete technical parameters for our BB5 API 610 horizontal barrel-type multistage between-bearings centrifugal pump. The BB5 is the highest pressure rating among API 610 pumps, designed for ultra-high pressure, high temperature critical services such as refinery hydrogenation feed, ultra-supercritical boiler feed, ethylene plant process, and ultra-high pressure water injection.
Performance Range
| Parameter | Value |
|---|---|
| Flow rate | 5 ~ 1,000 m³/h (22 ~ 4,400 GPM) |
| Total head | 300 ~ 2,000 m (984 ~ 6,560 ft) – higher on request |
| Speed | 1480 rpm / 2980 rpm (50/60 Hz) or custom high speed |
| Medium temperature | -50°C ~ +450°C (-58°F ~ +842°F) |
| Maximum working pressure | Up to 220 bar (3,190 psi) – higher on request (up to 400 bar) |
| NPSHr | Optimized low NPSH hydraulic design (inducer optional) |
Structure & Mechanical Design
Type: Horizontal barrel multistage between bearings (API 610 BB5 designation)
Casing: Full barrel pressure-containing design – no axial split, maximum pressure integrity
Rotor: Cartridge inner assembly – the complete rotor (impellers, shaft, bearings, wear rings, interstage bushings) is removable as a single cartridge. Maintenance can be performed without removing the barrel casing or disconnecting piping.
Number of stages: 3 ~ 15 stages customizable to achieve exact head requirement
Mounting: Centerline support – even thermal expansion at high temperature, prevents misalignment
Bearings: Sleeve bearing (for high speed/low vibration) or tilting pad bearing (for extreme loads)
Lubrication: Forced oil lubrication (standard for high speed BB5 pumps) – ensures reliable cooling and film strength at high pressure
Sealing: API 682 cartridge mechanical seal (all plans) – dry gas seal option available for hydrogen, light hydrocarbon, or non-lubricating fluids
Material Options
| Component | Standard Materials | Upgrade Options |
|---|---|---|
| Barrel casing | Alloy steel (high pressure), high-strength carbon steel | Ductile iron for lower pressure, 316L |
| Inner casing / diffuser | 316L stainless steel | Duplex, super duplex, high chromium alloy |
| Impeller | 316L, duplex, high chromium alloy | 17-4PH, Inconel, Hastelloy |
| Shaft | Forged high-strength alloy steel (AISI 4140, 4340) | 316L, duplex, K500 |
| Wear rings & bushings | Anti-corrosion & anti-abrasion alloy | Colmonoy-coated, ceramic, Stellite |
Available Technical Documents (Free Request)
API 610 data sheet (fully filled with your operating conditions)
Installation dimension drawing (2D CAD, PDF/DWG)
Performance curve (head, efficiency, NPSHr vs flow, including multiple trims)
3D model (STEP/IGES for plant design integration)
Material certificate (EN 10204 3.1 or 3.2)
Hydrostatic and performance test report (witnessed or unwitnessed)
Key Design Features Explained
Full Barrel Pressure-Containing Casing
The BB5 barrel has no axial split. All high-pressure containment is within a seamless, forged or fabricated barrel. This eliminates gasket leak paths and allows the pump to safely operate at extreme pressures (200–400+ bar).
Cartridge Rotor Assembly
Unlike segmental or axial split pumps, the BB5's entire rotating element is a cartridge. To overhaul, you remove the barrel end cover and pull the cartridge out horizontally. The barrel stays in place, piping remains connected. This reduces maintenance downtime by up to 50% compared to non-cartridge designs.
Centerline Mounting
For high temperature services (up to 450°C), centerline mounting ensures that the casing expands evenly around the shaft centerline. Foot-mounted pumps would tilt or bind, causing seal and bearing failure.
Forced Oil Lubrication
High speed and high pressure generate significant bearing heat. Forced oil (pressurized circulation) provides consistent cooling, filtration, and oil film thickness, ensuring 24/7 reliability.
Dry Gas Seal Option
For hydrogen, ethylene, methane, or other light hydrocarbons where product leakage is unacceptable, we offer tandem dry gas seals (API 682 Type B or C). These use nitrogen or process gas as a barrier, achieving zero emissions to atmosphere.
Why Accurate BB5 Pump Technical Specifications Matter
Engineers specifying BB5 pumps for hydrogenation units or ultra-high pressure boiler feed rely on precise data for:
Determining safe working pressure vs. temperature limits
Selecting the correct number of stages and diffuser type
Designing foundation and piping for nozzle loads
Integrating 3D models into plant layout (PDMS, SmartPlant, AutoCAD Plant 3D)
Specifying API 682 seal plan and flushing arrangement
Planning maintenance intervals and spare cartridge inventory
All our BB5 pump technical data is verified by hydraulic simulation, finite element analysis (FEA) for pressure containment, and factory performance testing per API 610.
Get Your BB5 Pump Technical Specification Package
To request a complete documentation package with a formal quotation, please send us your operating conditions:
Flow rate (m³/h or GPM)
Total head (m or ft)
Working pressure (bar or psi)
Temperature (°C or °F)
Fluid name (specify hydrogen, hydrocarbon, water, etc.)
Any special requirement (NACE, dry gas seal, low NPSH, high speed)
Our engineering team will respond within 24 hours with:
Recommended BB5 pump model (stage count, barrel size)
Performance curve PDF
API 610 data sheet
2D CAD drawing and 3D model link
Material and seal recommendations
Factory direct price (EXW / FOB / CIF) and delivery time
Email: info@hyrig.com
We are a professional API 610 pump manufacturer (BB1, BB2, BB3, BB4, BB5, OH types) serving global refineries, petrochemical complexes, hydrogenation units, ultra-supercritical power plants, and high-pressure injection projects. Contact us for custom-engineered BB5 pumps at factory direct wholesale pricing.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.