Blowdown Pump | API 610 OH2 Centrifugal Pump | China OH2 Pump Manufacturer

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
API 610 OH2 single‑stage, overhung pump for blowdown service (boiler blowdown, cooling tower basin drain, process vessel bottom drain). Handles hot water (up to 150°C), suspended solids, and intermittent operation. Corrosion resistant materials. China OH2 pump manufacturer.

Conatct For Details
DetailReview(0)Additional

A blowdown pump removes concentrated or contaminated liquid from a system – typically from boilers (bottom blowdown or surface blowdown), cooling tower basins, or process vessels. The fluid may be hot (boiler blowdown up to 150°C or higher after flash cooling), contain suspended solids (sludge, scale, silt), and often has high pH or dissolved solids. Our API 610 OH2 centrifugal pump is specifically engineered for reliable blowdown transfer in power plants, refineries, chemical plants, and industrial facilities. This design fully complies with API 610 11th/12th edition (ISO 13709) .

Structure match check: API 610 OH2 is defined as a horizontal, single‑stage, overhung pump with foot‑mounted casing and back pull‑out design. This matches blowdown service requirements because:

  • OH2 provides easy maintenance – back pull‑out for impeller, seal, and bearings without disturbing piping – important for often dirty, intermittent blowdown streams.

  • Wide hydraulic coverage (flow 5‑1000 m³/h, head up to 150 m) suits typical blowdown transfer duties.

  • Solids handling – semi‑open or open impeller with replaceable wear plate passes small particles (scale, sludge).

  • High temperature capability – with proper materials and seal plan, handles hot blowdown up to 150°C.

Why API 610 OH2 for blowdown duty?

  • Solids handling – Blowdown often contains scale particles, sludge, or crystallized salts. Open or semi‑open impeller with wear plate prevents clogging and extends life.

  • High temperature capability – Boiler blowdown can be 100‑150°C (after flash tank). Centreline support optional; bearing housing cooling and Plan 23 seal (cooled recirculation) or Plan 32 (external flush) recommended.

  • Corrosion resistance – Blowdown may be acidic (pH from CO₂) or alkaline (high pH from boiler chemicals). Wetted parts: 316SS, duplex, or high‑chrome iron. Carbon steel not recommended for long life.

  • Intermittent duty robustness – Blowdown pumps often start/stop automatically. Heavy duty bearings and API 682 seals handle frequent cycling.

  • Easy cleaning – Casing bottom drain and top vent for flushing settled solids.

  • Wide range – Flow from 5 m³/h (small boiler blowdown) to 1000 m³/h (cooling tower basin sump).

Key design features for blowdown service

  • Materials – Casing: 316SS or duplex for corrosive blowdown; cast iron with epoxy coating for mild service. Impeller: semi‑open or open, hardened 17-4PH or 316SS with hardened wear plate. Shaft: 316SS or 17-4PH. Wear plate: replaceable, hardened stainless.

  • Impeller type – Semi‑open (recommended) passes solids up to 10‑15 mm. Open impeller for larger solids (up to 25 mm). Fully enclosed only for clean blowdown.

  • Sealing – Plan 11 (internal recirculation) adequate for clean, cool blowdown. For hot blowdown (>80°C): Plan 23 (cooled recirculation) or Plan 32 (external water flush) to cool seal faces. For abrasive solids: Plan 31 (cyclone) or Plan 32. Gland packing optional for low cost, but requires periodic adjustment.

  • Bearing housing – Oil lubricated. For hot blowdown (>100°C), cooling fan or water jacket. For intermittent duty, oil bath is sufficient.

  • Casing drain – Minimum 1.5” NPT full port drain for solids removal.

  • Vent – High point vent to release trapped air during filling.

Typical performance range

ParameterValue
Flow rate5 – 1000 m³/h
HeadUp to 150 m
TemperatureUp to 150°C (higher with cooling)
Pressure ratingUp to 20 bar
Solids passage (semi‑open)Up to 15 mm
Speeds1450 / 2900 / 3600 rpm

Typical applications

  • Boiler bottom blowdown – Periodic discharge from mud drum.

  • Boiler surface blowdown – Continuous or intermittent removal of dissolved solids.

  • Cooling tower blowdown – Removing concentrated water from basin to drain or treatment.

  • Process vessel drain – Pumping sumps or blowdown from reactors, evaporators.

  • Blowdown flash tank transfer – After pressure reduction and cooling.

Why choose our API 610 OH2 blowdown pump?

  • Full API 610 compliance – Performance test, mechanical run test (4 hours) with vibration monitoring.

  • Solids handling design – Semi‑open impeller + wear plate ensures reliable operation with scale and sludge.

  • High temperature capability – Seal plans (Plan 23/32) and bearing cooling extend life.

  • Easy maintenance – Back pull‑out for rapid cleaning or part replacement.

  • Short lead time – Standard 316SS blowdown pumps available 8‑12 weeks.

  • Global spare parts support – Impellers, wear plates, shafts, seals, bearings shipped worldwide.

Quality assurance

  • ISO 9001:2015 certified.

  • API 610 mechanical run test with vibration and bearing temperature monitoring.

  • Hydrostatic test of casing.

  • Material traceability EN 10204 3.1 / 3.2.

  • NDE – MT, PT as required.

How to specify your blowdown pump

Please provide: flow (m³/h), head (m), blowdown source (boiler, cooling tower, process), temperature (°C), solids content and size (mm), fluid composition (pH, chlorides, acids), NPSHa (m), and intermittent or continuous duty. We will recommend impeller type (semi-open/closed), seal plan (11/23/32), material grade (316SS/duplex/cast iron), and driver details.

Contact us

For a quotation or technical discussion on blowdown pumps (API 610 OH2) :

info@hyrig.com


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit