A crude oil main pump (also called mainline crude pump or pipeline pump) moves large volumes of crude oil over long distances in pipelines, or from storage to process units in refineries. This service demands very high flow rates, moderate to high heads, continuous 24/7 operation, and high efficiency. Our API 610 BB1 horizontally split, single‑stage, double‑suction pump is the industry standard for this critical duty. This design fully complies with API 610 11th/12th edition (ISO 13709) .
Structure match check: API 610 BB1 is defined as a horizontal, axially split, single‑stage, between‑bearings pump with double‑suction impeller. This matches crude oil mainline requirements because:
Axially split casing allows removal of the top half for inspection and maintenance (wear rings, impeller) without disconnecting suction/discharge piping – essential for high‑availability pipeline service.
Double‑suction impeller hydraulically balances axial thrust, eliminating the need for complex thrust bearings and extending component life.
Between‑bearings rotor provides maximum shaft rigidity, minimizing deflection under high radial loads typical of high flow crude.
High efficiency (typically 85‑90%) reduces energy cost significantly for pumps that may run 8,000 hours/year.
Wide flow range (up to 25,000 m³/h) covers trunk pipeline and refinery feed duties.
Why API 610 BB1 for crude oil main pump duty?
Very high flow capacity – single‑stage design can handle flows from 500 to 25,000 m³/h, covering most crude pipeline requirements (e.g., 24‑48 inch pipelines).
High efficiency – Double‑suction design minimizes recirculation losses. Hydraulic optimization achieves 85‑90% efficiency at design point, saving megawatts of power.
Low NPSH – Double‑suction impeller inherently lowers NPSHr compared to single‑suction, important for pipeline pump stations where suction pressure may be limited.
Easy maintenance – Top‑half casing removal gives full access to impeller, wear rings, and internal passages. No need to break pipe flanges for routine inspection.
Long life – Between‑bearings and balanced thrust mean bearings last years. Heavy duty oil lubricated bearings (pure oil mist optional). Stellite wear rings are standard.
High temperature handling – Suitable for preheated crude (up to 150°C or higher) with proper materials and thermal expansion design.
Key design features for crude oil mainline service
Casing – Axially split, with suction and discharge flanges in lower half (standard) or both halves. Centerline support for thermal expansion if crude is heated. Material: carbon steel (WCB, WCC, LCC) for standard crude; low temperature carbon steel (LCC) for cold climates/waxy crude.
Impeller – Double‑suction, single‑stage. Hydraulically balanced, dynamically balanced. Material: stainless steel (CA6NM, 17-4PH) or carbon steel with stainless overlay. Replaceable wear rings on both sides.
Shaft – Large diameter, short span between bearings. Material: 4140 or stainless (17-4PH). With replaceable shaft sleeve under seals.
Wear rings – Replaceable, hardened stainless (17-4PH) or Stellite. Clearance designed for crude oil.
Bearings – Heavy duty anti‑friction (ball and roller) or tilting pad journal for very large pumps. Oil lubricated (splash or forced). Bearing housings with labyrinth seals. Pure oil mist standard or optional.
Sealing – API 682 single mechanical seal (Plan 11 or 13) for clean crude. For volatile crude or emissions control, tandem seals with Plan 52 (unpressurized buffer) or double seals with Plan 53A. Seal faces: SiC vs. carbon or SiC vs. SiC.
Driver – Electric motor (typically 4‑12 pole, 12‑60 MW) or gas turbine. Variable frequency drive (VFD) for flow control.
Impeller trim – Available trimmed to exact duty point for optimum efficiency.
Nozzle orientation – Top suction / top discharge standard; side suction / top discharge optional.
Typical performance range
| Parameter | Value |
|---|---|
| Flow rate | 500 – 25,000 m³/h |
| Head | Up to 250 m (higher with two-stage configuration) |
| Temperature | -40°C to +200°C |
| Pressure rating | ASME Class 150 – 600 (up to 110 bar) |
| NPSHr | 3 – 8 m (varies with flow and impeller design) |
| Speeds | 750 – 3600 rpm |
| Efficiency | Up to 90% |
Typical applications
Long‑distance crude oil trunk pipelines (mainline pumping stations).
Refinery crude unit feed pumps (from storage to CDU).
Oil terminal crude transfer – ship unloading to tank farm (high flow, low head).
Pipeline booster stations (intermediate lift).
Heavy crude pipelines with preheat (above pour point).
Why choose our API 610 BB1 crude oil main pump?
Full API 610 compliance – Type BB1 verified. Performance test, NPSH test, 4‑hour mechanical run test with vibration monitoring.
High efficiency hydraulic design – CFD optimized for crude oil viscosity (2‑20 cSt typical). Reduces energy cost.
Double‑suction reliability – No axial thrust issues, smooth operation, long bearing life.
Easy inline maintenance – Top‑half casing removal without breaking pipe connections.
Short lead time – Standard pump sizes with carbon steel casing and stainless trim available 20‑24 weeks.
Global spare parts support – Casing halves, impeller, shaft, wear rings, bearings, seal cartridges shipped worldwide.
Quality assurance
ISO 9001:2015 certified.
API 610 mechanical run test (minimum 4 hours) with vibration and bearing temperature monitoring.
Hydrostatic test of casing at 1.5× working pressure.
Material traceability EN 10204 3.1 / 3.2.
NDE – MT, PT, UT as required.
Impeller and rotor dynamic balancing grade G2.5.
How to specify your crude oil main pump
Please provide: flow (m³/h), head (m), crude API gravity / viscosity (cSt at pumping temperature), temperature (°C), suction pressure (bar), NPSHa (m), pipeline diameter (if known), required material class (carbon steel / low temp carbon steel), and any emissions regulations. We will recommend impeller diameter, casing pressure rating, seal plan (11/52/53A), bearing lubrication (oil bath or oil mist), and driver type.
Contact us
For a quotation or technical discussion on crude oil main pumps (API 610 BB1) :
info@hyrig.com
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.