We are a professional China OH6 pump manufacturer, offering high‑quality API 610 compliant vertical in‑line overhung pumps with an integral speed‑increasing gearbox. Unlike standard motor‑speed pumps, our OH6 series incorporates a built‑in gearbox that steps up the input speed (typically from 1450/1500 rpm or 2900/3000 rpm motor to much higher impeller speeds). This design achieves small flow rates with very high heads – a combination that is difficult or inefficient with direct‑drive pumps. The OH6 is the ideal solution for high‑speed processes, condensate systems, and any application requiring high pressure at low flow.
What is an OH6 Pump?
According to API 610, the OH6 pump is a vertical in‑line, single‑stage overhung centrifugal pump with an integral speed‑increasing gearbox. The gearbox is mounted between the motor and the pump end, increasing the impeller rotational speed significantly above the motor’s synchronous speed. Key characteristics:
Small flow range (typically 1 – 150 m³/h, often below 50 m³/h for very high head)
Very high head capability (often 200 – 800+ meters, depending on speed and impeller design)
Compact vertical in‑line footprint – mounts directly on pipeline flanges
Integral gearbox – no external coupling or separate gear unit; factory‑aligned and sealed
High speed operation (impeller speeds can reach 6,000 – 20,000 rpm or higher)
Why Choose Our China OH6 Pump?
When you search for a reliable China OH6 pump manufacturer, you need a supplier who understands high‑speed rotating machinery, API 610 requirements, and the unique demands of small flow / high head services. Our OH6 pumps are engineered for:
High‑pressure condensate return systems
Boiler feed water boosting (small boilers)
High pressure chemical injection
Hydrocarbon processing with low flow but high differential pressure
Cryogenic or high temperature high‑speed duties (with appropriate materials and seals)
Applications where a multistage pump is too large, expensive, or inefficient
Designed for Typical Working Conditions
Our China OH6 pumps run reliably in:
High speed, high head, small flow processes
Continuous 24/7 operation in refineries, petrochemical plants, power stations
Condensate systems (including hot condensate up to 180°C or higher with special seals)
High pressure water or chemical injection services
Low flow hydrocarbon transfer with high differential pressure
Normal to moderately high temperatures (-40°C to +200°C, depending on gearbox oil and seal selection)
Clean or slightly contaminated liquids (abrasives accelerate wear at high speed)
Compatible Media
The OH6 pump is best suited for clean, low‑viscosity liquids that allow stable high‑speed operation:
Condensate (steam condensate, high temperature water)
Boiler feed water
Light hydrocarbons (propane, butane, naphtha, light gasoline) with low viscosity
Chemical injection fluids (amines, methanol, corrosion inhibitors)
High pressure water jets, descaling water
Heat transfer fluids (low viscosity)
Cryogenic liquids (with appropriate cold‑service gearbox design)
**Avoid abrasive or solid‑laden fluids – high tip speeds will cause rapid impeller and seal wear.
Key Technical Features
Standard: API 610 (11th edition), API 682 for mechanical seals, AGMA gear standards
Design: Vertical in‑line, single‑stage overhung, integral speed‑increasing gearbox
Mounting: Directly on vertical pipeline flanges (suction and discharge in‑line) or on a small baseplate
Drive: Electric motor (standard speed) + integral gearbox (single‑stage or multi‑stage speed increase)
Impeller speed: Typically 3,000 – 20,000 rpm (customizable)
Flow: 1 – 150 m³/h (standard); up to 300 m³/h on request
Head: Up to 1,200 meters (depending on speed and impeller design)
Temperature: -40°C to +200°C (higher or lower with special gearbox oil and seals)
Materials: Carbon steel, stainless steel (304, 316), duplex, super duplex (for corrosive high‑head services)
Flanges: ANSI, ASME, DIN, JIS (higher pressure ratings common – up to Class 1500)
Gearbox: Integral, splash or forced oil lubrication, cooling coil for high temperature duties
Shaft sealing: Mechanical seals (API 682 Type A, B, or C) with high speed rating; seal support system required
Product Advantages
Small flow + high head in one stage – eliminates the need for multistage pumps or very large high‑speed motors with external frequency drives
Integral gearbox – factory‑aligned, leak‑tight, space‑saving, no external coupling misalignment issues
Vertical in‑line footprint – saves floor space compared to horizontal multistage pumps
API 610 compliance – heavy‑duty construction for continuous high‑speed service
Efficient at low flow – avoids the low flow instability and recirculation problems of larger pumps run far to the left on their curve
Cost‑effective alternative – lower cost than a multistage horizontal pump (OH2 type) for many low flow / high head services
Custom speed tuning – we can match the gear ratio to your exact duty point
One‑Stop Full Service
As a leading China OH6 pump manufacturer, we provide a complete one‑stop service for high‑speed pumps:
Selection & hydraulic calculation – we use high‑speed pump design software to match flow, head, and NPSH requirements.
Custom gearbox design – gear ratio, lubrication type, cooling, and materials for your temperature range.
Manufacturing – precision gear cutting, dynamic balancing of high‑speed rotor, API 610 quality checks.
High‑speed testing – vibration analysis, bearing temperature monitoring, performance curve verification (optional).
Delivery – lead time typically 8–12 weeks for custom high‑speed units.
Installation & commissioning – on‑site supervision for critical high‑speed alignment and startup.
After‑sales – spare gearbox parts, high‑speed seals, bearing sets, technical support.
Main Applications
Condensate return and boosting systems (power plants, refineries, steam plants)
Boiler feed water (small to medium industrial boilers)
High pressure chemical injection (oil & gas, petrochemical)
Hydrocarbon processing – low flow, high differential pressure (e.g., reactor feed, wash oil)
High pressure water descaling in steel mills
Reverse osmosis high pressure booster (small flow high pressure stage)
Cryogenic high head services (LNG, liquid nitrogen)
Pilot plants and small process units requiring high pressure at low flow
Frequently Asked Questions (FAQ)
Q: What is the difference between OH6 and other API 610 pump types?
A: The key difference is the integral speed‑increasing gearbox. Standard pump types (OH1, OH2, OH3, OH4, OH5) operate at motor speed (1450–2900 rpm typically). The OH6 uses a built‑in gearbox to drive the impeller at much higher speeds (e.g., 6,000–20,000 rpm), achieving high head with a small impeller. For very high head / low flow, the OH6 is often more compact and cost‑effective than a multistage OH2 pump.
Q: Can I use an OH6 pump for high temperature condensate?
A: Yes, but you must specify high temperature gearbox lubrication (synthetic oil, possibly with external cooling). Standard cast iron/carbon steel OH6 pumps suit temperatures up to 150–180°C. For higher temperatures, we recommend sealed gearbox with forced oil cooling and high temperature mechanical seals. Consult our engineers.
Q: Is a special motor required?
A: No. The OH6 pump is designed to accept a standard industrial motor (NEMA or IEC). The gearbox increases the speed. However, the motor must have sufficient power for the high head duty; we calculate the required power and provide motor recommendations.
Q: How reliable is the integral gearbox?
A: When properly designed and maintained, very reliable. We use precision ground gears, heavy‑duty bearings, and splash or forced lubrication. For continuous high speed service, we recommend scheduled oil analysis and gearbox inspection per API 610 guidelines.
Q: What is the typical NPSH requirement for OH6 pumps?
A: High speed pumps generally require higher NPSH than low speed pumps. For very high speeds (e.g., >10,000 rpm), NPSHr can be 5–10 meters or more. We will calculate NPSHr for your duty point and advise on system NPSHa. In some cases, a low‑speed inducer can be added.
Q: Do you stock OH6 pumps?
A: OH6 pumps are typically engineered‑to‑order due to the wide variation in gear ratios, speeds, materials, and seals. We do not stock finished units, but we maintain inventory of gearbox components, bearings, and seals to shorten lead times (usually 8–12 weeks). Standard moderate‑speed OH6 pumps with limited customization may be available in 6–8 weeks.
Why Choose Us as Your China OH6 Pump Supplier
Specialized engineering team for high‑speed pump and gearbox design
In‑house dynamic balancing and high‑speed testing rigs
API 610 compliance with full traceability
Competitive pricing – significantly lower than Western high‑speed pump specialists
Fast technical response – we help you select OH6 vs. multistage OH2 for your duty
Complete documentation – performance curves, vibration reports, lubrication schedule
Global shipping with export packaging
Contact Us
For inquiries, technical support, or a custom quotation for our high‑speed China OH6 pump, please contact us at:
info@hyrig.com
Choose our China OH6 pump – high speed, small flow, high head, and built for the toughest high‑pressure vertical pipeline duties.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.