A cooling water pump (also called circulating water pump or cooling tower pump) delivers large volumes of water to cool condensers, heat exchangers, and process equipment. The service demands high flow rates, moderate heads, continuous operation, and high efficiency. Our API 610 BB1 and OH2 pumps cover two different design philosophies – both fully compliant with API 610 11th/12th edition (ISO 13709) – depending on flow, head, and space requirements.
API 610 BB1 – Axially Split, Single‑Stage, Double‑Suction Pump
Structure match check: API 610 BB1 is defined as a horizontal, axially split, single‑stage, between‑bearings pump with double‑suction impeller. This is the classic “horizontal split case” design for high flow, moderate head services.
Why BB1 for cooling water?
High flow capacity – from 500 to 25,000 m³/h (or more). Ideal for main circulating water in power plants and large refineries.
Dual suction impeller – hydraulically balanced axial thrust, allowing higher speeds and simpler bearing design.
High efficiency – double‑suction design typically achieves 85-90% efficiency, reducing energy cost significantly for large flows.
Easy maintenance – axially split casing allows removal of top half to inspect impeller, wear rings, and internal passages without disconnecting piping.
Low NPSH – double‑suction impeller inherently reduces NPSHr compared to single‑suction.
Robust construction – between‑bearings rotor with short shaft span provides long bearing life.
Head range – up to 150 m, but typically 20-80 m for cooling tower service.
Typical BB1 applications
Main circulating water pumps for power plant condensers.
Refinery and petrochemical cooling tower return pumps.
Industrial process cooling loops (steel, chemical, paper mills).
Large HVAC primary pumps (district cooling).
API 610 OH2 – Single‑Stage, Overhung Pump
Structure match check: API 610 OH2 is defined as a horizontal, single‑stage, overhung pump with foot‑mounted casing and back pull‑out design. This is suitable for smaller cooling water duties where flow is below approximately 800 m³/h.
Why OH2 for cooling water?
Compact size – smaller footprint than BB1 for low to moderate flows (5 – 800 m³/h).
Lower cost – simpler construction, lower initial investment for smaller duties.
Back pull‑out maintenance – rotor, seal, and bearings can be removed without disturbing piping.
Good efficiency – 75-85% typical for water service.
Wide availability – standard materials (cast iron or carbon steel) suitable for clean cooling water.
Head range – up to 150 m.
Typical OH2 applications
Auxiliary cooling water pumps for smaller plants.
Cooling tower fill pumps (side‑stream).
Equipment jacket cooling (compressors, engines).
HVAC chilled water pumps (secondary loops).
Comparison & Selection Guide
| Feature | BB1 (Split Case) | OH2 (Overhung) |
|---|---|---|
| API 610 type | BB1 – between‑bearings, axially split, double‑suction | OH2 – overhung, foot‑mounted |
| Flow range | 500 – 25,000 m³/h | 5 – 800 m³/h |
| Head range | Up to 150 m | Up to 150 m |
| Impeller | Double‑suction (axial thrust balanced) | Single‑suction (requires thrust bearing) |
| Casing access | Remove top half – full internal access | Back pull‑out – rotor only |
| Efficiency | 85-90% | 75-85% |
| Best for | Large flow, continuous, high efficiency | Smaller flow, lower cost, space saving |
| Maintenance | Inline casing stays; top half removal | Rotor removal without piping |
Key design features for cooling water service (both types)
Materials – Casing: cast iron (ASTM A48) or carbon steel (WCB) for clean water. For brackish or seawater, specify 316SS, duplex, or bronze fitted. Impeller: bronze (ASTM B148) or stainless steel for corrosion resistance, especially in seawater cooling. Shaft: 316SS or carbon steel with stainless sleeve. Wear rings: bronze or stainless.
Sealing – For clean cooling water, single mechanical seal with Plan 11 (recirculation) or gland packing (low cost). For environmental compliance or critical service, tandem seals with Plan 52/53A.
Bearing housing – Oil lubricated, with cooling fan for ambient >40°C. Pure oil mist optional for continuous duty.
NPSH – Cooling water pumps often have ample NPSH from cooling tower basins or ponds. However, for low NPSH conditions (e.g., suction lift from basin), inducer option on OH2 or special impeller design on BB1.
Corrosion protection – For seawater or brackish water, internal coatings (epoxy) or solid bronze/duplex construction.
Impeller trimming – Both types can be trimmed to match exact duty point, saving energy.
Efficiency verification – We provide hydraulic performance curves witnessed per API 610.
Why choose our API 610 cooling water pumps?
Full API 610 compliance – BB1 and OH2 types verified. Performance test, mechanical run test.
High efficiency design – CFD optimized hydraulics reduce energy cost – critical for 24/7 cooling water service.
Corrosion resistant options – Epoxy coating, bronze impellers, stainless steel for aggressive water.
Easy maintenance – BB1: top‑half casing removal; OH2: back pull‑out.
Long bearing life – Conservative bearing selection and oil mist option.
Short lead time – Standard cast iron pumps ex‑stock; bronze/stainless 8-12 weeks.
Global spare parts support – Casings, impellers, shafts, bearings, seals shipped worldwide.
Quality assurance
ISO 9001:2015 certified.
API 610 mechanical run test (4 hours minimum) with vibration and bearing temperature monitoring.
Hydrostatic test of casing.
Material traceability EN 10204 3.1 / 3.2.
Impeller dynamic balance.
How to specify your cooling water pump
Please provide: flow (m³/h), head (m), water type (clean fresh, brackish, seawater, cooling tower with chemicals), temperature (°C), NPSHa (m), required material (cast iron / carbon steel / bronze / stainless), and preferred configuration (BB1 for large flow, OH2 for small). We will recommend pump type, impeller trim, seal plan, material class, and driver details.
Contact us
For a quotation or technical discussion on cooling water pumps (API 610 BB1 or OH2) :
info@hyrig.com
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.