Cup Tester – SYD Series – Complete Product Introduction

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
Cup tester is mainly used for casing pressure testing. For oil, gas, and water wells that have been run in casing and equipped with wellhead devices, it can perform layer pressure testing once for the casing and BOP system. It can also be used for casing pressure testing in pipe yards. The pressure testing process is very convenient: simply run the cup tester into the casing. Available in numerous models (SYD104 to SYD493) covering casing sizes from 4‑1/2″ to 20″ and a wide range of casing weights. Connections include NC26, NC31, NC38, NC50.

Conatct For Details
DetailReview(0)Additional

Overview
The cup tester is a downhole tool primarily used for casing pressure testing. For oil, gas, and water wells where casing has been run and a wellhead device is already installed, the cup tester can perform layered pressure testing of both the casing and the BOP (blowout preventer) system in a single run. It can also be used for casing pressure testing in pipe yards (e.g., testing casing joints before running in hole). The pressure testing process is extremely convenient: simply run the cup tester into the casing to the desired depth, then apply pressure. The cup expands to seal against the casing ID, isolating the section below for pressure testing.

Key Features

  • Casing & BOP Testing – Tests both casing integrity and BOP system in one run.

  • Layer Pressure Testing – Isolates specific casing sections for pressure verification.

  • Convenient Operation – No complex setup; run in, pressure up, retrieve.

  • Wide Casing Coverage – Models for 4‑1/2″ to 20″ casing with various weights.

  • Multiple Connections – NC26, NC31, NC38, NC50 (depending on model).

  • Pipe Yard Use – Can test casing strings on the ground before running.

Working Principle
The cup tester is run on drill pipe to the desired depth inside the casing. The tool has one or more rubber cups (sealing elements) that are slightly smaller than the casing ID when relaxed. When hydraulic pressure is applied from the surface (through the pipe or the annulus), the pressure activates the cup, expanding it radially to seal against the casing wall. The sealed section below the cup can then be pressurized to the desired test pressure (e.g., 5,000 psi or higher). Pressure is monitored at surface. If the pressure holds steady, the casing and/or BOP are considered intact. After testing, pressure is bled off, the cup contracts, and the tool is retrieved.

Technical Specifications (Representative Models – Full Range Available)

ModelTool OD mm (inch)Tool ID mm (inch)OAL mm (ft)Casing Size (inch)Casing Weight (lb/ft)Connection
SYD10488.9 (3-1/2)20 (25/32)651 (2.1)4-1/215.1NC26 B×P
SYD106–108(various)——4-1/211.6–13.5, 9.5–10.5NC26
SYD125104.8 (4-1/8)25.4 (1)660 (2.2)5-1/223NC31 B×P
SYD128–131———5-1/217–20, 14–15.5NC31
SYD163127 (5)25.4 (1)710 (2.3)729–32NC38 B×P
SYD166–170———723–26, 17–20NC38
SYD222165.1 (6-1/2)50.8 (2)787 (2.6)9-5/853.5NC50 B×P
SYD227–231———9-5/843.5–47, 36–40NC50
SYD245165.1 (6-1/2)50.8 (2)815 (2.7)10-3/473.2NC50 B×P
SYD249–258———10-3/465.7, 45.5–51NC50
SYD321–328165.1 (6-1/2)50.8 (2)815 (2.7)13-3/868–72, 61, 54.5, 48NC50
SYD379–388165.1 (6-1/2)50.8 (2)900 (3.0)16109, 84NC50
SYD458165.1 (6-1/2)50.8 (2)935 (3.1)18-5/887.5NC50
SYD483–493165.1 (6-1/2)50.8 (2)980 (3.2)20133, 106.5, 94NC50

Note: For exact specifications of intermediate models (SYD106–108, SYD128–131, etc.), please contact us. Custom specifications and other casing sizes are available upon request – refer to the technical agreement for details.

Applications

  • Pressure testing of casing strings after running and cementing

  • Combined casing and BOP system pressure test before drilling ahead

  • Isolated layer pressure testing in multi‑zone wells

  • Casing pressure test in pipe yards (pre‑running inspection)

  • Onshore and offshore oil, gas, and water wells of all sizes

Value Proposition

  • One Tool, Multiple Tests – Tests casing, BOP, and layering in one run.

  • Extremely Convenient – Simple run‑in and pressurize operation.

  • Wide Casing Compatibility – Dozens of models cover 4‑1/2″ to 20″ casing, all common weights.

  • Reliable Sealing – Cup design provides effective isolation for accurate pressure measurement.

  • Time Saving – No need for multiple trips or complex packer settings.

The SYD series cup tester is the go‑to tool for efficient, reliable casing pressure testing – whether in the well after casing installation or in the pipe yard before running. Its simple design and broad size range make it an essential tool for well integrity verification.

Contact Us
For technical data sheets, exact model selection based on casing weight, or a quotation, please contact:
Email: info@hyrig.com


Cup Tester – Simplify casing pressure testing, one run, reliable results.


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit