Deep Well Pump | API 610 VS1 Vertical Turbine Pump | China VS1 Pump Manufacturer

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
API 610 VS1 vertical, single‑casing, lineshaft turbine pump for deep wells, boreholes, and water supply. Multistage, high efficiency, long column length (up to 100m). Suitable for clean water, dewatering, and industrial applications. China VS1 pump manufacturer.

Conatct For Details
DetailReview(0)Additional

A deep well pump (vertical turbine pump) is used to extract water from deep boreholes, wells, or underground sources where the water level is far below ground surface. Our API 610 VS1 vertical, single‑casing, lineshaft turbine pump is specifically engineered for reliable, high‑efficiency deep well service. This design fully complies with API 610 11th/12th edition (ISO 13709) .

Structure match check: API 610 VS1 is defined as a vertical, single‑casing, lineshaft pump with bowl assembly and impellers that are either open or enclosed, typically multistage. It is designed for installation in a well or borehole with the pump below ground and the driver above ground. This matches deep well pump requirements because:

  • The pump bowl assembly (with multiple stages) is submerged below the water level, with a long shaft extending up to the surface-driven motor or engine.

  • Lineshaft bearings (product‑lubricated or grease‑packed) support the shaft at intervals, allowing column lengths up to 100 meters or more.

  • Water enters through a suction screen or bell at the bottom, passes through multistage diffuser/impeller bowls, and is discharged up the column pipe.

  • The design handles clean water, slightly abrasive water, or even corrosive fluids with proper materials.

Why API 610 VS1 for deep well duty?

  • High lift capability – Multistage design (2 to 30+ stages) provides heads from 50 to 800 meters, ideal for deep wells.

  • High efficiency – Each stage is hydraulically optimised, achieving overall pump efficiencies of 80‑86% for water.

  • Customizable column length – Pump bowl set at any depth below dynamic water level.

  • Small footprint – Vertical installation occupies minimal surface area.

  • Easy maintenance – The entire pump (bowl assembly, column, shaft) can be pulled from the well for servicing (though requires a derrick or crane).

  • Wide flow range – 10 to 4000 m³/h, covering municipal water supply, irrigation, industrial dewatering, and groundwater remediation.

Key design features for deep well service

  • Bowl assembly – Cast iron or stainless steel bowls with diffuser vanes. Multistage with impellers stacked on a common shaft.

  • Impellers – Enclosed (for efficiency) or semi‑open (for slight abrasives). Material: bronze, stainless steel, or polyamide (for non‑corrosive). Replaceable wear rings.

  • Column pipe – Carbon steel (epoxy coated) or stainless steel. Flanged connections. Length custom to well depth.

  • Lineshaft – High strength alloy or stainless steel. Supported by intermediate bearings (every 1.5‑3 m).

  • Bearings – Water‑lubricated rubber bearings for clean water; grease‑packed bearings for non‑lubricating fluids.

  • Suction bell / screen – Prevents large debris entry. Optional foot valve.

  • Discharge head – At surface, with flanged outlet, supports driver (electric motor or right‑angle gear drive). Contains top shaft bearing and mechanical seal or packing.

  • Driver – Vertical hollow‑shaft electric motor (most common) or diesel engine with right‑angle gear drive.

  • Materials for corrosion – For saline or acidic water: 316SS bowl and impellers, duplex stainless steel shaft.

Typical performance range

ParameterValue
Flow rate10 – 4000 m³/h
Head50 – 800 m
Stages2 – 30
Column lengthUp to 150 m (longer on request)
Well diameter requirementMinimum 150 mm (6 inches) for smallest sizes
TemperatureUp to 50°C standard (higher on request)

Typical applications

  • Municipal water supply – Deep well pumping to treatment plants.

  • Irrigation – Agricultural wells, center pivot supply.

  • Industrial dewatering – Quarries, mines, construction sites.

  • Groundwater remediation – Pump and treat systems.

  • Oil & gas – Water supply for drilling or injection (clean water).

  • Cooling water – For plants with deep well sources.

Why choose our API 610 VS1 deep well pump?

  • Full API 610 compliance – Type VS1 verified. Performance test, mechanical run test.

  • High efficiency hydraulics – Reduced energy cost over decades of operation.

  • Durable materials – Stainless steel trim for long life in corrosive water.

  • Custom bowl setting depth – Matched to your well static/dynamic water level.

  • Short lead time – Standard bowl sizes and column pipe in stock; assembly 12‑16 weeks.

  • Global spare parts support – Bowls, impellers, column pipes, lineshaft bearings, discharge heads shipped worldwide.

Quality assurance

  • ISO 9001:2015 certified.

  • API 610 mechanical run test (4 hours) with vibration monitoring.

  • Hydrostatic test of column and discharge head.

  • Material traceability EN 10204 3.1.

  • Impeller dynamic balancing.

How to specify your deep well pump

Please provide: flow (m³/h), head (m), well depth (m) from surface to bowl setting, dynamic water level (m), well casing inside diameter (inches), water quality (clean, sandy, corrosive), temperature (°C), and driver type (electric motor / engine). We will recommend number of stages, bowl size, impeller material (bronze/SS), column material, and lineshaft bearing type.

Contact us

For a quotation or technical discussion on deep well pumps (API 610 VS1) :

info@hyrig.com


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit