A fuel oil pump handles heavy fuel oil (HFO), bunker fuel, residual oil, or intermediate fuel oils (IFO) used in boilers, furnaces, and marine diesel engines. Fuel oil is typically viscous (50‑1000+ cSt at pumping temperature), may require heating to reduce viscosity, and often contains residual solids (asphaltenes, cat fines). Our API 610 OH2 centrifugal pump is specifically engineered for reliable fuel oil transfer and circulation. This design fully complies with API 610 11th/12th edition (ISO 13709) .
Structure match check: API 610 OH2 is defined as a horizontal, single‑stage, overhung pump with foot‑mounted casing and back pull‑out design. This matches fuel oil service requirements because:
Back pull‑out allows seal, bearing, and impeller inspection without disturbing piping – important for viscous fluids that may require cleaning.
With speed reduction (e.g., 1450 rpm or lower) and proper impeller trimming, OH2 can handle viscosities up to 1000 cSt.
Steam jacketed casing and seal housing options are available for heavy fuel oil that requires heating (to 50‑100°C for pumpability).
Foot‑mounted casing with option for centerline support if temperature >100°C.
Why API 610 OH2 for fuel oil duty?
Viscosity handling – Standard centrifugal pumps lose head/efficiency at high viscosity. We correct performance using HI (Hydraulic Institute) viscosity correction factors, often specifying lower speed (e.g., 1450 rpm instead of 2900 rpm) and larger impellers to maintain duty.
Heating provisions – For heavy fuel oil (HFO), steam jacketed casing and seal housings keep fluid fluid and prevent solidification. Optional electric heat tracing.
Abrasion resistance – Fuel oil may contain catalyst fines (cat fines) from refineries. Hardened 12% chrome or Stellite wear rings; semi‑open impeller with replaceable wear plate.
Reliable sealing – For hot, viscous fuel oil, typical seal plan: Plan 11 (internal recirculation) with flushed seal chamber. Plan 62 for quench to prevent coking. For zero emission requirements, double seals with Plan 53A (pressurized barrier oil).
Wide temperature range – Fuel oil pumped at 50‑150°C (heated). Carbon steel casing with stainless trim.
Flow range – 5 to 1500 m³/h, head up to 200 m.
Key design features for fuel oil service
Materials – Casing: carbon steel (WCB / WCC) for standard; 316SS for corrosive fuel oils. Impeller: hardened 12% chrome (CA6NM) or 17‑4PH for abrasion. Shaft: 17‑4PH or 12% chrome.
Impeller type – Closed for clean fuel oil; semi‑open with wear plate for cat fines or sludges.
Viscosity correction – Pump selection with de‑rated head, flow, efficiency, and NPSH using HI viscosity correction factors. Lower speed (1200‑1800 rpm) preferred.
Heating – Steam jacket on casing (optional). Steam connections (1/2" or 3/4") on lower casing and seal gland.
Sealing – API 682 Plan 11 with jacketed seal housing. Plan 62 (steam quench) for preventing coke buildup. For emissions, Plan 53A double seals with barrier fluid compatible with fuel oil.
Bearing housing – Oil lubricated, with cooling fan or water jacket if operating at high ambient. For extended life, pure oil mist.
Drain – Full port bottom drain for complete removal of viscous fuel during maintenance.
Typical performance range (viscosity corrected)
| Parameter | Value |
|---|---|
| Flow rate | 5 – 1500 m³/h |
| Head | Up to 200 m |
| Viscosity range | 1 – 1000 cSt (higher with heating) |
| Temperature | Up to 150°C (with steam jacketing) |
| Pressure rating | Up to 20 bar |
| Speeds | 750 – 2900 rpm (lower for high viscosity) |
Typical applications
Boiler fuel oil supply – Transfer from day tank to burner.
Bunker fuel transfer – From storage to ship or to settling tanks.
Refinery fuel oil forwarding – To coker, visbreaker, or fuel oil blending.
Marine engine fuel supply – For auxiliary engines (HFO).
Thermal power plants – Fuel oil circulation.
Why choose our API 610 OH2 fuel oil pump?
Full API 610 compliance – Performance test with viscosity‑corrected evaluation, mechanical run test.
Viscosity expertise – We select correct speed, impeller size, and heating requirements for your fuel oil grade.
Steam jacketed design – Keeps heavy fuel oil fluid, prevents solidification.
Abrasion protection – Hardened materials for cat fines and asphaltenes.
Short lead time – Standard carbon steel/12% chrome pumps with heating jackets available 12‑16 weeks.
Global spare parts support – Impellers, wear plates, shafts, seals, bearings, steam jackets shipped worldwide.
Quality assurance
ISO 9001:2015 certified.
API 610 mechanical run test (4 hours) with vibration monitoring.
Hydrostatic test of casing.
Material traceability EN 10204 3.1 / 3.2.
NDE – MT, PT as required.
How to specify your fuel oil pump
Please provide: flow (m³/h), head (m), fuel oil grade (e.g., IFO380, HFO, marine diesel), viscosity at pumping temperature (cSt), pumping temperature (°C), specific gravity, cat fines content (yes/no), NPSHa (m), and required material (carbon steel / stainless). We will recommend speed, impeller diameter, heating jacket (yes/no), seal plan (11/62/53A), and driver details.
Contact us
For a quotation or technical discussion on fuel oil pumps (API 610 OH2) :
info@hyrig.com
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.