A hot oil pump circulates high temperature heat transfer fluids (thermal oils) in closed loop systems used for indirect heating in refineries, chemical plants, asphalt terminals, plastics, and food processing. These fluids can operate at 250‑400°C, well above the boiling point of water, and require a pump designed for extreme thermal expansion, high temperature sealing, and reliable continuous duty. Our API 610 OH2 high temperature pump is specifically engineered for hot oil / thermal fluid service. This design fully complies with API 610 11th/12th edition (ISO 13709) with special high temperature adaptations.
Structure match check: API 610 OH2 is defined as a horizontal, single‑stage, overhung pump with back pull‑out design. For high temperature service (>120°C), API 610 requires centreline support rather than foot mounting to allow thermal expansion without misalignment. Our hot oil pump meets this requirement. Additional high temperature features include:
Centreline support casing – allows expansion along axis, avoiding distortion.
Water cooled bearing housing – maintains bearing temperature within limits (typically <70°C).
Raised seal housing with cooling jacket – reduces seal face temperature.
High temperature mechanical seal with Plan 23 (cooled recirculation) – the standard for hot oil.
Material selection – WC6 (1¼Cr-½Mo) or WC9 (2¼Cr-1Mo) alloy steel casing for creep resistance up to 400°C.
Why API 610 OH2 for hot oil duty?
High temperature capability – Continuous operation at 400°C with WC6/WC9 casing, stainless steel impeller/shaft, and thermal expansion allowances.
Centreline support – Prevents thermal growth misalignment; avoids coupling and bearing problems.
Water cooled bearings – Bearings are isolated from casing heat by a cooling jacket (water circulation) or fin fan. Bearing life extended.
Plan 23 sealing – Cooled recirculation keeps seal faces below coking temperature. For very high temperature (>350°C), Plan 32 with external cool oil injection may be used.
High temperature gaskets – Spiral wound with graphite filler; no elastomers.
Thermally robust design – Larger internal clearances (wear rings) at ambient to prevent rubbing at operating temperature.
Wide hydraulic range – Flow 5 to 1500 m³/h, head up to 200 m.
Key design features for hot oil service
Casing – Centreline support, axially split (footprint) or radially split casing. Material: WC6 (up to 450°C) or WC9 (up to 480°C). Pressure rating ASME Class 300 typical.
Impeller – Closed, radial, dynamically balanced. Material: 12% chrome (CA6NM) or 17‑4PH. Wear rings: hardened 17‑4PH, clearance calculated for thermal growth.
Shaft – High strength alloy (17‑4PH or AISI 4140), with replaceable shaft sleeve under seal.
Bearing housing – Water jacketed (cooling connections ½" NPT). Oil lubricated. Pure oil mist optional.
Sealing – API 682 Plan 23: thermosiphon or pumped recirculation through a fin‑fan cooler or water cooled heat exchanger, returning cool oil to seal chamber. For zero emissions: double seals with Plan 53A (barrier fluid cooled). Seal faces: SiC vs. SiC.
Gaskets – Graphite spiral wound for casing joints, no rubber. O‑rings replaced with PTFE or metal.
Insulation – Optional removable insulation blanket on casing to reduce heat loss.
Drains / vents – High point vent, low point drain for complete oil removal.
Typical performance range
| Parameter | Value |
|---|---|
| Flow rate | 5 – 1500 m³/h |
| Head | Up to 200 m |
| Temperature | Up to 400°C |
| Pressure rating | Up to 40 bar |
| Speeds | 1450 / 2900 rpm (lower speed preferred for high temp) |
Typical applications
Hot oil circulation in refinery reboilers and heater coils.
Chemical plant heat transfer (polymerisation, distillation).
Asphalt / bitumen heating and transfer with jacketed casing.
Plastics industry – extruder barrel heating.
Food processing – indirect heating for cooking or drying.
Solar thermal power plants – HTF circulation (synthetic oils).
Why choose our API 610 OH2 high temperature hot oil pump?
Full API 610 compliance with high temperature adaptations – centreline support, Plan 23 seal, water cooled bearings, alloy steel casing.
Proven reliability – Thousands of hot oil pumps in service worldwide with >3 years MTBR.
No thermal misalignment – Centreline support ensures stable operation.
Short lead time – Standard WC6 / WC9 sizes available 16‑20 weeks.
Global spare parts support – Casings, impellers, shafts, seal cartridges, water cooled bearing housings shipped worldwide.
Quality assurance
ISO 9001:2015 certified.
API 610 mechanical run test (4 hours) with vibration monitoring and bearing temperature recording. Heat not applied during test, but clearance measurements documented.
Hydrostatic test of casing at 1.5× working pressure.
Material traceability EN 10204 3.1 / 3.2.
NDE – MT, PT, UT for casing and shaft.
How to specify your hot oil pump
Please provide: flow (m³/h), head (m), thermal fluid type (e.g., Dowtherm, Therminol, Marlotherm), maximum operating temperature (°C), specific gravity at pump temperature, viscosity (cSt), NPSHa (m), required material (WC6 / WC9), and cooling water availability. We will recommend impeller trim, seal plan (23/53A), bearing cooling type (water jacket or fin fan), and driver details.
Contact us
For a quotation or technical discussion on hot oil pumps (API 610 OH2 high temperature) :
info@hyrig.com
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.