This page presents verified field cases of our API 610 OH4 vertical overhung centerline mounted sump pumps operating reliably in high temperature sump and pit services up to 400°C. Each case demonstrates the pump's key advantages – centerline mounting for thermal stability, no submerged bearing for low maintenance, and custom sump depth capability for challenging installations.
Case 1 – Refinery High Temperature Sump (Middle East)
Background: A refinery required a reliable pump for recovering hot oily water from a process unit sump at 320°C (608°F). Foot-mounted pumps experienced thermal misalignment, seal failures, and bearing distress. Conventional OH3 pumps could not handle the temperature.
OH4 Pump Solution:
Flow: 160 m³/h
Head: 35 m
Temperature: 320°C
Sump depth: 2,200 mm
Material: Carbon steel (high temp grade), 316L impeller
Features: Centerline mounting, cooling jacket on bearing housing, dry-run protection
Results:
No thermal displacement – centerline mount eliminated misalignment even after repeated heat cycles
Long stable operation – over 2.5 years without unplanned downtime
No submerged bearing – no failures from sand or hot water contamination
Maintenance reduced to annual upper bearing lubrication only
Available references: Site photo, installation drawing, thermal expansion record.
Case 2 – Petrochemical High Temp Corrosive Sump (Southeast Asia)
Background: A petrochemical plant had a sump collecting high temperature (280°C) corrosive process medium containing chlorides. Standard 316L pumps showed pitting after 6 months. The plant needed a corrosion-resistant, leak-free solution.
OH4 Pump Solution:
Flow: 95 m³/h
Head: 28 m
Temperature: 280°C
Sump depth: 1,500 mm
Material: Duplex stainless steel (casing, impeller, shaft)
Features: Centerline mount, no submerged seal, cooling jacket
Results:
Anti-corrosion – duplex material withstood chlorides at high temperature without pitting (2+ years)
Leakage-free – no submerged seal means zero leakage of hazardous chemicals
Reliable high temp operation – centerline mount prevented thermal distortion
The plant standardized on OH4 duplex pumps for all high temp corrosive sumps
Available references: Material certificate (EN 10204 3.1), installation photo, corrosion inspection report.
Case 3 – Power Plant Thermal Sump System (Asia)
Background: A thermal power plant needed multiple pumps for a high temperature condensate pit collecting hot condensate (160°C) from HRSG and turbine drains. Low vibration and automatic control were required.
OH4 Pump Solution:
Four OH4 pump sets (2 duty + 2 standby across two pits)
Flow per pump: 220 m³/h
Head: 22 m
Temperature: 160°C
Sump depth: 1,800 mm
Material: Carbon steel casing, stainless steel impeller
Features: Centerline mount, automatic level control system
Results:
Low vibration – well within API 610 limits, thanks to rigid cantilever design
Reliable running – continuous operation for 18 months without any pump failure
Automatic control – level sensors started/stops pumps as sump filled
No submerged bearings – pumps handled intermittent operation without issue
Available references: Control system schematic, site photos, vibration log.
Case 4 – Chemical Deep Sump Pumping (Europe)
Background: A chemical facility had an underground deep sump (3,200 mm) collecting residual liquid from tank cleaning operations. The liquid was slightly corrosive at 90°C. Access was limited to the top of the sump.
OH4 Pump Solution:
Flow: 55 m³/h
Head: 18 m
Temperature: 90°C
Sump depth: Custom 3,200 mm
Material: 316L stainless steel
Features: Extra-long cantilever shaft, strainer, dry-run protection
Results:
Efficient and low maintenance – custom long sump depth matched exact pit depth
No intermediate bearings – simple, reliable, no submerged components to fail
Easy top access – entire rotating assembly pulls from above, no need to enter sump
The facility reduced tank cleaning downtime by 40%
Available references: Custom installation drawing, site photo, maintenance log.
What You Can Request From Us for Each Case
Site photos and installation images
Installation drawings (sump pit layout, mounting details)
Project parameter sheet (flow, head, temperature, depth, material)
Operation reference data (run hours, maintenance intervals)
Why Real Project Cases Matter
Field references prove that our OH4 pumps deliver:
No thermal displacement at 320°C+ in refinery hot oily sump service (centerline mount advantage over OH3)
Corrosion resistance and leak-free performance in high temp corrosive sumps (duplex)
Low vibration, reliable operation in power plant condensate pits
Efficient deep sump recovery with custom long cantilever shafts
Get the Complete OH4 Pump Case Study Package
We can match your high temperature sump conditions to similar successful installations. Request the OH4 pump project case PDF or ask for references in your specific industry.
Email: info@hyrig.com
Please specify your industry (refinery hot sump / petrochemical corrosive / power plant condensate / chemical deep sump) and we will send relevant case studies, installation drawings, and technical data within 24 hours. We also welcome inquiries for custom OH4 high temperature sump pump selection and factory direct pricing.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.