A sludge pump handles thick, abrasive, and often corrosive slurry containing suspended solids, organic matter, and fibrous material – typical in wastewater treatment plants, industrial effluent processes, mining tailings, and dredging operations. Our API 610 OH2 centrifugal pump is specifically engineered for reliable sludge and heavy slurry service. This design fully complies with API 610 11th/12th edition (ISO 13709) .
Structure match check: API 610 OH2 is defined as a horizontal, single‑stage, overhung pump with foot‑mounted casing and back pull‑out design. This matches sludge pump requirements because:
Back pull‑out allows seal, bearing, and impeller inspection without disturbing piping – essential for frequent cleaning in sludge service.
Open or semi‑open impeller with replaceable wear plate passes solids (up to 15‑25 mm) and protects the casing from abrasive wear.
Robust bearing housing with oversized anti‑friction bearings handles the high radial loads from heavy slurries.
Slow speed options (e.g., 750‑1200 rpm) reduce wear and maintain efficiency with high viscosity sludge.
Heavy duty shaft minimizes deflection, extending seal and bearing life.
Why API 610 OH2 for sludge duty?
Solids handling – Open impeller with large passages (up to 25 mm spherical solids) prevents clogging. Semi‑open impeller for moderate solids with higher efficiency.
Abrasion resistance – Wetted parts in high chrome white iron (Cr27), Ni‑Hard, or rubber‑lined. Replaceable wear plates and throatbush extend service life.
Corrosion resistance – For aggressive sludge (low pH, high chlorides), stainless steel 316SS or duplex available.
Low speed operation – Reduced impeller tip speed minimises erosion. Efficiency maintained by larger impeller diameter.
Easy maintenance – Back pull‑out plus drop‑out casing (optional) for full access.
Wide viscosity range – Handles sludge up to 1000 cSt with performance de‑rating.
Flow range – 10 to 2000 m³/h, head up to 80 m.
Key design features for sludge service
Impeller type – Open (maximum solids passage, lower efficiency) or semi‑open (good balance). Designed with back vanes to reduce seal pressure.
Wear plate – Replaceable, hardened high chrome or rubber. Adjustable for maintaining impeller clearance as wear occurs.
Materials – Casing: high chrome (Cr27), duplex stainless, or rubber‑lined carbon steel. Impeller: high chrome or natural rubber. Shaft: 17‑4PH or 4140 with stainless sleeve.
Sealing – For abrasive sludge, Plan 31 (cyclone separator) or Plan 32 (external clean water flush) to protect seal faces. Gland packing alternative for low cost and abrasion tolerance. For zero emissions, double seals with Plan 53A.
Bearing housing – Heavy duty taper roller bearings, oil lubricated, with labyrinth seals to prevent ingress of sludge dust/water. Cooling fan optional.
Casing drain – Full port flush port to flush settled solids during shutdown.
Speed – Typically 750‑1450 rpm (4‑8 pole motor). VFD optional.
Typical performance range
| Parameter | Value |
|---|---|
| Flow rate | 10 – 2000 m³/h |
| Head | Up to 80 m |
| Solids passage (open impeller) | Up to 25 mm |
| Temperature | Up to 80°C |
| Speeds | 750 / 1000 / 1450 rpm |
Typical applications
Municipal wastewater treatment – Primary, secondary, or digested sludge transfer.
Industrial effluent – Chemical plant sludges, pulp and paper mill sludge.
Mining – Tailings, thickener underflow.
Dredging – Light dredging of settling ponds.
Food processing – Sludge from wastewater treatment.
Why choose our API 610 OH2 sludge pump?
Full API 610 compliance – Performance test, mechanical run test.
Abrasion and corrosion resistant – High chrome or rubber lining options.
Easy solids removal – Open impeller, large flush port, back pull‑out.
Long life – Heavy bearings, oversized shaft, slow speed operation.
Short lead time – Standard high chrome sizes available 12‑16 weeks.
Global spare parts support – Impellers, wear plates, shafts, seals, bearings shipped worldwide.
Quality assurance
ISO 9001:2015 certified.
API 610 mechanical run test (4 hours) with vibration monitoring.
Hydrostatic test of casing.
Material hardness verification for high chrome parts.
Material traceability EN 10204 3.1.
How to specify your sludge pump
Please provide: flow (m³/h), head (m), solids concentration (% dry solids), particle size (mm), sludge type (raw, digested, industrial), pH and chlorides (for material selection), temperature (°C), NPSHa (m). Also indicate if fibrous materials present. We will recommend impeller type (open/semi‑open), material (high chrome / rubber / stainless), seal plan (31/32/packing), speed, and driver details.
Contact us
For a quotation or technical discussion on sludge pumps (API 610 OH2) :
info@hyrig.com
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.