Flare KO Drum Pump | API 610 VS4 & OH2 | China Flare System Pump Manufacturer

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
API 610 VS4 vertical suspended and OH2 horizontal pumps for flare knock-out drum liquid removal. Pump condensate, seal oil, water from KO drum to slop or treatment. Low NPSH design, intermittent duty. Corrosion resistant materials. China flare system pump manufacturer.

Conatct For Details
DetailReview(0)Additional

A flare knock-out drum pump (flare KO drum pump) removes accumulated liquid (condensate, seal oil, water, or other hydrocarbons) from the bottom of a flare knock-out drum. The KO drum separates liquid from gas before the gas goes to the flare stack; the pump transfers the liquid to slop systems, oily water treatment, or storage. This service requires intermittent operation, low NPSH (often flooded suction), and ability to handle light hydrocarbons, water, or mixture. Our API 610 VS4 and OH2 pumps are specifically engineered for this duty. Both designs fully comply with API 610 11th/12th edition (ISO 13709) .


API 610 VS4 – Vertical Suspended Pump

Structure match check: API 610 VS4 is defined as a vertical, single‑casing, rigid shaft, suspended pump with discharge head above the pit/drum cover. This is ideal when the KO drum has limited horizontal space, or when a vertical pump can be installed directly on the drum top flange.

Why VS4 for flare KO drum?

  • Direct mount on drum nozzle – no suction piping, flooded suction.

  • Small footprint – minimal external space.

  • Low NPSH – impeller submerged below lowest liquid level.

  • Intermittent duty robust – bearings and seals suitable for start‑stop cycles.

  • Easy maintenance – pump can be withdrawn without draining the drum (if provision for isolation valves is limited, but typically requires depressuring).

  • Flow range – 2 to 200 m³/h (small to moderate).

  • Head – up to 100 m.

Typical VS4 applications

  • Flare KO drums on refineries, petrochemical plants, LNG terminals.

  • Seal drum or blowdown drum liquid removal.


API 610 OH2 – Horizontal Overhung Pump

Structure match check: API 610 OH2 is defined as a horizontal, single‑stage, overhung pump with foot‑mounted casing and back pull‑out design. This is suitable when the KO drum is located at grade and horizontal space is available, or the pump is installed at grade adjacent to the drum.

Why OH2 for flare KO drum?

  • Lower initial cost for above‑ground installation.

  • Easy access for maintenance (back pull‑out).

  • Wide hydraulic range (2 – 500 m³/h, head up to 150 m).

  • Suitable for flooded suction from KO drum (drum elevation provides NPSH).

  • Corrosion resistant materials available.

Typical OH2 applications

  • Flare KO drums with adequate NPSHa (drum elevated).

  • Intermittent transfer to slop or treatment.


Key design features for flare KO drum service (both types)

  • Materials – Casing: carbon steel for clean condensate; 316SS for corrosive or acidic water. Impeller: 316SS or bronze. Shaft: 316SS or 17‑4PH.

  • Sealing – For intermittent duty with hydrocarbons, single mechanical seal with Plan 11 (recirculation) is sufficient. For zero emissions (volatile compounds), tandem seal with Plan 52.

  • NPSH – KO drum typically provides flooded suction (liquid level above pump inlet). Low NPSHr not critical unless drum is small.

  • Intermittent operation – Frequent start/stop cycles: oversized bearings and API 682 seals rated for cycling.

  • Low flow protection – Minimum flow recirculation line (Plan 12 or 13) to prevent overheating during low/no flow.

  • Drain and vent – Full drain to remove settled water/sediment.

Why choose our API 610 flare KO drum pumps?

  • Full API 610 compliance – VS4 and OH2 types verified.

  • Reliable intermittent duty design – seals and bearings handle frequent cycling.

  • Corrosion resistant options – for sour or acidic condensate.

  • Short lead time – standard sizes available 8‑12 weeks.

  • Global spare parts support – impellers, seals, shafts, bearings.

Quality assurance

  • ISO 9001:2015 certified.

  • API 610 mechanical run test (4 hours) with vibration monitoring.

  • Hydrostatic test of casing.

  • Material traceability EN 10204 3.1.

How to specify your flare KO drum pump

Please provide: flow (m³/h), head (m), liquid composition (hydrocarbon, water, H₂S, pH), temperature (°C), NPSHa (m), drum elevation (for horizontal vs vertical selection), and installation preference. We will recommend VS4 or OH2, material class, seal plan, and driver details.

Contact us

For a quotation or technical discussion on flare knock-out drum pumps (API 610 VS4 / OH2) :

info@hyrig.com


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit