DIN Y Strainer RFQ Checklist | PN, Mesh & Open Area

2026-11-19 19:49

DIN Y Strainer RFQ Checklist

HYRIG can supply DIN Y-strainers. Because the standard defines specific face-to-face lengths and the mesh selection affects pressure drop, an incomplete RFQ often leads to a strainer that fits the flanges but blinds too quickly or requires a piping modification.

Key Facts

  • Standard: Specify BS EN 13709 and DIN 3202 F1, not just "DIN strainer".
  • Mesh: Specify the micron opening, not just the mesh count.
  • Open area: Confirm the open area percentage against the dirt loading of the line.
  • Flange drilling: Specify EN 1092-1 / DIN 2543–2551, not ASME B16.5.

Key Specifications

To receive a correctly sized strainer, provide the following data in your RFQ:

Data FieldWhy It Is Needed
StandardConfirms BS EN 13709 and DIN 3202 F1 as the design basis.
DNNominal size, determines the flange OD and screen diameter.
PNPressure rating, determines the body thickness and flange drilling.
Face-to-Face SeriesSpecify DIN 3202 F1 to match the piping gap.
Mesh / MicronSpecify the opening in micron; mesh count alone can be ambiguous.
Open AreaConfirm the open area percentage to estimate pressure drop and cleaning interval.
MaterialSpecify body and screen material (e.g., GS-C25, 1.4308, F304).
DocumentationState if EN 10204 3.1 certificates and DIN 3230 test reports are required.

Dimensions

DimensionStandard
Face-to-faceDIN 3202 F1 / BS EN 558-1
Flange drillingDIN 2543–2551 / EN 1092-1

Structure and Working Principle

The most common RFQ error is specifying only the mesh count, not the micron opening. A 100 mesh screen can have different opening sizes depending on wire diameter. Specify the opening in micron to avoid ambiguity.

The second common error is omitting the open area. A screen with 27.6% open area blinds faster than one with 51.8%. If the line carries high debris, a larger open area or a basket strainer may be required.

The third error is mixing flange standards. EN 1092-1 and ASME B16.5 are not interchangeable. Specify the correct flange drilling to avoid a mismatch at installation.

Cross-Reference and Replacement

When ordering a replacement DIN Y-strainer:

  1. Measure the existing gap: Record the face-to-face length and match it to DIN 3202 F1.
  2. Check the mesh: Confirm the existing mesh or micron rating to ensure the replacement matches the filtration requirement.
  3. Check the flange drilling: Confirm EN 1092-1 or DIN 2543–2551 to match the mating flanges.
  4. Verify documentation: For classified lines, specify EN 10204 3.1 certificates and DIN 3230 test reports.

Applications

  • New plant construction: Matching the line class and face-to-face series exactly.
  • Maintenance and replacement: Replacing a clogged or damaged strainer without modifying the piping.
  • Steam lines: Specifying 20–40 mesh with a Dutch weave screen for steam trap protection.
  • Pump suction: Specifying 10–20 mesh with a high open area to avoid cavitation.

Disclaimer: This equipment is designed for high-pressure industrial applications. Ensure strict compliance with local safety standards and verify pressure ratings prior to installation.

Frequently Asked Questions

Q: Why do I need to specify the F-series face-to-face?

Because DIN 3202 defines the length. DN and PN alone do not uniquely define the face-to-face dimension. F1 is the standard for PN16–PN25 Y-strainers.

Q: What is the most important field for dirty service?

The open area percentage and the mesh size. A screen with a larger open area blinds more slowly, but a finer mesh captures smaller particles.

Q: Do I need to specify the screen material?

Yes. ASTM A182 F304 is standard, but for corrosive media, a different grade may be required.

Q: What is the typical lead time?

Standard lead time is 4–6 weeks depending on size, PN rating, material, and documentation.

Selection Support

To ensure the DIN Y-strainer matches your piping and filtration requirement, provide the DN, PN, existing gap, mesh, and material. Our engineering team will verify the specification.

Contact

For DIN Y-strainer RFQ support, contact HYRIG: info@hyrig.com

Related Pages

Name:
Message:
Verification code:
Submit
Comment