DIN Y Strainer | PN16–PN25, DIN 3202 F1 Face-to-Face

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
HYRIG can supply the DIN Y-strainer range. The DIN Y-strainer is a compact pipeline protector with an angled screen chamber, designed to BS EN 13709 with face-to-face dimensions per DIN 3202 F1.
Conatct For Details
DetailReview(0)Additional

DIN Y Strainer

HYRIG can supply the DIN Y-strainer range. The DIN Y-strainer is a compact pipeline protector with an angled screen chamber, designed to BS EN 13709 with face-to-face dimensions per DIN 3202 F1. It is available in PN16 and PN25, with mesh sizes from 5 to 300 and stainless steel screens.

Key Facts

  • Design standard: BS 1873, BS EN 13709
  • Pressure rating: PN16 / PN25
  • Size range: DN15–DN600 (PN16)
  • Face-to-face: DIN 3202 F1, BS EN 558-1
  • Flange drilling: DIN 2543–2551 / EN 1092-1
  • Screen material: ASTM A182 F304
  • Body material: DIN 17245 GS-C25, DIN 17445 1.4308
  • Testing: DIN 3230, BS EN 12569

Key Specifications

DNPN16 L (mm)PN16 H (mm)PN25 L (mm)PN25 H (mm)
151309813098
25160108160108
50230150230150
100350245350245
150480335480335
200600415600415
300850570850570
40011006181100618
60014508901450890

Data source: Technical data table.

Mesh and Open Area Reference

MeshWire Dia A (SWG)Opening B (mm)Open Area D (%)
20280.35651.8
40360.19348.4
60380.15241.0
80400.12237.8
100420.10235.8
200470.05135.8
300480.03927.6

Data source: Technical data table.

Dimensions

DimensionStandard
Face-to-faceDIN 3202 F1 / BS EN 558-1
Flange drillingDIN 2543–2551 / EN 1092-1
Pressure-temperatureDIN 3230 / EN 1092-1

Structure and Working Principle

The flow enters the angled screen chamber, passes through the stainless steel screen, and exits through the outlet. Debris larger than the screen opening is captured on the inside of the screen. The angled chamber allows gravity to collect debris at the bottom, away from the flow path.

The DIN Y-strainer is compact and can be installed in horizontal or vertical lines with the screen chamber pointing downward. It is a permanent pipeline component, not a temporary startup device; the screen is cleaned by removing the bonnet or, if equipped, by opening a blowdown valve at the drain port.

Cross-Reference and Replacement

Replacing a DIN Y-strainer? Verify these before ordering:

  1. Face-to-face series: Confirm the existing valve uses DIN 3202 F1. DN and PN alone are not enough to define the length.
  2. Mesh and opening: Confirm the required micron rating, not just the mesh count. 40 mesh is about 193 micron; 100 mesh is about 102 micron.
  3. Open area ratio: A screen with 27.6% open area blinds faster than one with 51.8%. Check the open area against the dirt loading of the line.
  4. Flange drilling: DIN 2543–2551 and EN 1092-1 are not interchangeable with ASME B16.5. Confirm the mating flange standard.

Applications

  • Steam lines: Protects steam traps and control valves from pipe scale and weld slag.
  • Pump suction: Captures debris before it reaches the impeller; 10–20 mesh is typical for centrifugal pumps.
  • Meter and instrument protection: 60–100 mesh screens protect flowmeters and analyzers.
  • European-standard plant piping: DIN/EN flange drilling and face-to-face allow direct replacement in European-designed systems.

Disclaimer: This equipment is designed for high-pressure industrial applications. Ensure strict compliance with local safety standards and verify pressure ratings prior to installation. Blowdown operations must be performed with appropriate isolation and personal protective equipment.

Frequently Asked Questions

Q: What is the difference between DIN 3202 F1 and F2 for Y-strainers?

F1 is the short pattern used for PN16 and PN25; F2 is longer and used for higher PN ratings. They are not dimensionally interchangeable.

Q: Can a DIN Y-strainer be installed vertically?

Yes, with the screen chamber pointing downward. Upward-pointing installation prevents debris from settling and is not recommended.

Q: Does a Y-strainer need a blowdown valve?

A blowdown valve is recommended for dirty fluids and sizes above DN50. Clean gas and small lines can be cleaned manually by removing the screen.

Q: What is the typical lead time?

Standard lead time is 4–6 weeks depending on size, PN rating, material, and mesh requirement.

Selection Support

To confirm the correct DIN Y-strainer size, mesh, and material for your line, provide the line size, PN rating, medium, downstream equipment, and dirt loading. Our engineering team will verify the screen opening and open area against your filtration requirement.

Contact

For DIN Y-strainer selection, contact HYRIG: info@hyrig.com

Related Pages

Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit