A high pressure process pump is required in refineries and petrochemical plants for services where discharge pressure exceeds the safe limit of axially split pumps (typically above 250 bar). Applications include hydrocracker feed, high‑pressure reactor circulation, methanol synthesis feed, and high‑pressure injection. Our API 610 BB5 radially split, multistage barrel pump is specifically engineered for these extreme duties. This design fully complies with API 610 11th/12th edition (ISO 13709) .
Structure match check: API 610 BB5 is defined as a horizontal, radially split, multistage, between‑bearings barrel pump. This is the correct standard type for high pressure process service because:
The cylindrical barrel casing (radially split) contains extremely high discharge pressure (up to 500 bar+) without leak‑prone split flanges. Only the end cover and head are flanged.
Multistage design (4‑15 stages) achieves very high heads (up to 3000 m) required for high pressure processes.
Between‑bearings rotor provides stability at high power and high speed.
The internal cartridge (rotating element, diffusers, stage pieces) can be withdrawn from the barrel for maintenance without removing piping – though radially split, this is similar to BB3/BB5 style maintenance.
Higher pressure rating than any axially split design.
Why API 610 BB5 for high pressure process duty?
Extreme pressure capability – Standard designs up to 500 bar, special designs up to 700 bar. Essential for hydrocrackers (typically 140‑200 bar but with transients) and high pressure injection.
High temperature – Up to 400°C with appropriate material (WC6, WC9, or duplex). Barrel casing with internal thermal sleeves.
Reliability – No casing gasket exposed to high pressure (only end cover gasket). Robust design with heavy wall barrel.
Safety – Total containment of high pressure hydrocarbon leakage. Preferred for H₂‑rich, high‑pressure H₂S service.
Opposed impeller arrangement – Hydraulic thrust balance eliminates balance drum (which can wear in high pressure service with abrasive feeds). This is typical for BB5 designs.
High efficiency – 80‑86% depending on stages and fluid.
Key design features for high pressure process service
Barrel casing – Solid forged (or cast) cylindrical body. Material: carbon steel (AISI 4130 / 4140 forged) or stainless for corrosive. Heat treated for high pressure integrity.
End cover & head – Flanged, with high pressure seals (metal O‑rings). Suction and discharge nozzles on the barrel or head depending on configuration.
Internal cartridge – Consists of shaft, opposed impellers (back‑to‑back), diffusers, interstage bushings, and end bearings. Cartridge can be removed axially after removing end cover.
Impellers – Hardened 12% chrome (CA6NM) or 17‑4PH, with Stellite wear rings. Opposed orientation for thrust balance. First stage often double‑suction for low NPSH.
Diffusers – Stationary vane rings, also hardened.
Shaft – Large diameter, high strength alloy (e.g., 17‑4PH, Inconel 718 for severe). Shaft sleeves replaceable.
Bearings – Tilting pad journal bearings + double‑acting Kingsbury thrust bearing. Pure oil mist lubrication standard, with forced oil optional. Water‑cooled bearing housings for high temperature.
Sealing – API 682 Plan 23 (cooled recirculation) for hot high‑pressure service. Double seals with Plan 53A for zero emissions (common in H₂ service). Seal chamber designed for very high pressure.
NPSH – First stage double‑suction or with inducer to keep NPSHr low, as suction pressure may be from previous train (but often adequate).
Materials for H₂ / H₂S – NACE MR0175 compliance mandatory for many high pressure processes. Barrel in low‑alloy steel with hardness controlled; impellers in 12% chrome with hardness <22 HRC.
Typical performance range
| Parameter | Value |
|---|---|
| Flow rate | 30 – 1500 m³/h |
| Head | Up to 3000 m |
| Discharge pressure | Up to 500 bar (higher on request) |
| Temperature | Up to 400°C |
| Speeds | 3000 – 10000 rpm (often with gearbox or high speed motor) |
| Stages | 4 – 15 |
Typical applications
Hydrocracker (HCU) feed pump – Very high pressure (150‑250 bar).
Hydrotreater high pressure feed – For ultra‑low sulfur diesel.
Methanol synthesis loop – High pressure recirculation.
Ammonia plant synthesis gas pump.
High pressure injection (water or chemical injection into pipelines or reactors).
Hydraulic haulage / hypercompressors (though often reciprocating, centrifugal BB5 for certain duties).
Why choose our API 610 BB5 high pressure process pump?
Full API 610 compliance – Type BB5 verified. Performance, NPSH, 4‑hour mechanical run test with vibration monitoring.
Safe containment – Forged barrel casing, no leak‑prone joints exposed to high pressure.
Opposed impeller design – No balance drum, longer life.
High temperature engineering – Plan 23 seals, water‑cooled bearings, WC9 casing.
Short lead time – Our manufacturing program for BB5 sizes 24‑40 weeks.
Global spare parts support – Complete cartridge (rotor + diffusers), bearings, seal cartridges, barrel casing shipped worldwide.
Quality assurance
ISO 9001:2015 certified.
API 610 mechanical run test (4 hours minimum) with vibration and bearing temperature monitoring.
Hydrostatic test of barrel casing at 1.5× working pressure.
Material traceability EN 10204 3.1 / 3.2 (forged barrel requires 3.2).
NDE – 100% UT on barrel, MT/PT on flanges, RT on welds.
Rotor dynamic analysis (lateral and torsional) per API 610.
How to specify your high pressure process pump
Please provide: flow (m³/h), head (m), discharge pressure (bar), temperature (°C), fluid (e.g., hydrocracker feed, H₂‑rich, sour crude), H₂S content (for NACE), NPSHa (m), required material (carbon steel / 12% chrome / duplex), and driver type. We will recommend number of stages, impeller orientation (opposed), seal plan (23/53A), bearing type, and barrel material.
Contact us
For a quotation or technical discussion on high pressure process pumps (API 610 BB5) :
info@hyrig.com
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.