A vertical sump pump is used to remove water or other liquids from pits, sumps, basements, or collection tanks where horizontal pumps cannot be placed due to space or suction conditions. Our API 610 VS4 vertical, single‑casing, rigid shaft pump is specifically engineered for reliable sump and pit service in industrial plants, refineries, chemical facilities, and power stations. This design fully complies with API 610 11th/12th edition (ISO 13709) .
Structure match check: API 610 VS4 is defined as a vertical, single‑casing, rigid shaft, suspended pump with discharge head above the pit cover. This matches sump pump requirements because:
The pump is suspended from a top plate above the pit, with the impeller submerged below the lowest operating level – ensuring flooded suction and no priming needed.
Column pipe can be customised from 1 to 10+ meters to reach bottom of deep sumps.
Small footprint – only a circular pit opening needed, leaving floor space free.
Top‑pull design allows entire pump to be withdrawn vertically for maintenance without dewatering the pit.
Rigid shaft with line‑shaft bearings (product lubricated) ensures stable operation at moderate speeds.
Why API 610 VS4 for vertical sump duty?
Flooded suction – No priming devices, no suction lift problems. Impeller is always submerged, preventing cavitation and dry running.
Space efficient – Takes up only the area of the pit cover. No baseplate extending horizontally.
Deep sump capability – Column lengths up to 10m or more, with intermediate bearings if needed.
Easy maintenance – Entire pump assembly (motor, discharge head, column pipe, impeller) can be lifted out by overhead crane. No need to enter the pit.
Corrosion / abrasion options – Engineered plastics, rubber linings, stainless steel, or bronze for aggressive sump liquids.
Wide application – Clean water, process sumps, oily water, mildly abrasive slurries.
Flow range – 5 to 3000 m³/h, head up to 100 m.
Key design features for vertical sump pump service
Discharge head – Cast iron, carbon steel, or stainless steel, with flanged discharge nozzle and motor support bracket. Bearing housing (oil lubricated) supports the shaft.
Column pipe – Carbon steel (with internal and external coating) or stainless steel. Flanged at both ends. Length customised to pit depth.
Line‑shaft bearings – Product‑lubricated (water or liquid) rubber bearings at intervals (e.g., every 1.5m) to support the shaft and prevent whipping. For non‑lubricating liquids, grease‑packed bearings.
Impeller – Mixed flow or radial flow. Open or semi‑open for solids passage. Materials: cast iron, bronze, 316SS, duplex, or hardened alloys. Replaceable wear ring or suction plate.
Shaft – Rigid, stainless or alloy steel, with replaceable sleeve in bearing areas.
Sealing – No mechanical seal needed below liquid level. At discharge head above pit, a simple rotary seal (lip seal or mechanical seal) or packing gland prevents splashing. Plan 01 (gland packing) or Plan 11 (recirculation) if mechanical seal.
Motor – Vertical hollow‑shaft electric motor (preferred) or solid‑shaft with flexible coupling. Mounted on discharge head.
Solids handling – Large internal passages, space between impeller and suction bell for small solids (up to 25mm depending on size).
Materials for corrosive sumps – 316SS or duplex for chemical pits; rubber‑lined or polyurethane for abrasive slurries.
Typical performance range
| Parameter | Value |
|---|---|
| Flow rate | 5 – 3000 m³/h |
| Head | Up to 100 m |
| Column length | 1 – 12 m (longer on request) |
| Temperature | Up to 80°C (higher with special materials) |
| Speeds | 750 – 2900 rpm |
| Solids passage | Up to 25 mm (open impeller) |
Typical applications
Industrial plant sump drainage – Machine coolant, washdown water.
Refinery oily water sumps – API separator pit.
Chemical plant collection pits – Acidic or caustic sumps (stainless or plastic lined).
Power plant basement drains – Turbine pit, condenser pit.
Mining dewatering – Light slurry sumps.
Municipal sewage lift stations (light duty, non‑clog design available).
Why choose our API 610 VS4 vertical sump pump?
Full API 610 compliance – Type VS4 verified. Performance test, mechanical run test.
Custom column length – Matched to your pit depth exactly.
Reliable product‑lubricated bearings – No external lube required for water sumps.
Easy maintenance – Top‑pull design, no pit entry.
Short lead time – Standard column lengths (2, 3, 4, 5m) available ex‑stock; custom lengths 8‑10 weeks.
Global spare parts support – Discharge heads, column pipes, shaft with bearings, impellers, line‑shaft bearings shipped worldwide.
Quality assurance
ISO 9001:2015 certified.
API 610 mechanical run test (4 hours) with vibration monitoring (for assembly).
Hydrostatic test of discharge head.
Material traceability EN 10204 3.1.
NDE – MT, PT as required.
How to specify your vertical sump pump
Please provide: flow (m³/h), head (m), pit depth (m) from cover to bottom, sump liquid (water, oily, chemical, slurry), temperature (°C), solids content and size, NPSHa (m) – usually ambient, and material preference (carbon steel coated / 316SS / bronze). We will recommend impeller type and size, column length, line‑shaft bearing type (rubber product lubricated or grease‑packed), and motor specification.
Contact us
For a quotation or technical discussion on vertical sump pumps (API 610 VS4) :
info@hyrig.com
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.