Tank Suction Pump | API 610 VS4 & VS5 Vertical Pump | China Tank Suction Pump Manufacturer

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
API 610 VS4 (short to medium column, rigid shaft) and VS5 (long column, lineshaft bearings) vertical pumps for tank suction from bulk storage. Used for chemicals, water, light hydrocarbons. Flooded suction, easy maintenance. China tank suction pump manufacturer.

Conatct For Details
DetailReview(0)Additional

A tank suction pump (also called vertical in‑tank pump or tank unloading pump) is installed directly on top of a storage tank, with the pump column extending down into the liquid. This configuration provides flooded suction, eliminates suction piping, and saves external floor space. Our API 610 VS4 and VS5 vertical pumps are specifically engineered for tank suction service in refineries, chemical plants, and bulk liquid terminals. Both designs fully comply with API 610 11th/12th edition (ISO 13709) , with different construction types based on column length and bearing requirements.


API 610 VS4 – Rigid Shaft Vertical Pump

Structure match check: API 610 VS4 is defined as a vertical, single‑casing, rigid shaft, suspended pump with discharge head above the tank flange. This is suitable for tank suction when the distance from the flange to the impeller is relatively short (typically ≤ 3 meters) and no intermediate bearings are needed.

Why VS4 for tank suction?

  • Rigid shaft – no intermediate bearings. Simple, low maintenance.

  • Ideal for smaller tanks or when suction bell is close to tank top.

  • Flooded suction – impeller submerged below lowest liquid level.

  • Easy assembly – fewer parts.

  • Flow range – up to 1000 m³/h, head up to 100 m.

  • Typical applications: small chemical tanks, water storage, intermediate tanks.


API 610 VS5 – Lineshaft Vertical Pump

Structure match check: API 610 VS5 is defined as a vertical, single‑casing, lineshaft, suspended pump with discharge head above the tank flange and one or more intermediate product‑lubricated (or grease‑packed) bearings along the column. This is required when the column length exceeds approximately 3 meters to prevent shaft whipping.

Why VS5 for tank suction?

  • Long column capability – up to 20 meters or more.

  • Intermediate lineshaft bearings (rubber or grease lubricated) support the shaft.

  • Suitable for large storage tanks (e.g., crude oil, refined products, chemical storage).

  • Flooded suction, no priming.

  • Flow range – up to 5000 m³/h, head up to 150 m.

  • Typical applications: large tank farms (chemicals, oil, water).


Comparison & Selection Guide

FeatureVS4 (Rigid Shaft)VS5 (Lineshaft)
API 610 typeVS4 – rigid shaft, single casingVS5 – lineshaft with intermediate bearings
Max column length≤ 3 m (no intermediate bearings)>3 m up to ~20 m
BearingsOnly in discharge headIntermediate product‑lubricated or grease bearings
Shaft typeOne piece rigid shaftMultiple sections with coupling
ComplexityLowModerate
Flow rangeUp to 1000 m³/hUp to 5000 m³/h
Best forSmall tanks, clean liquidsLarge tanks, deep liquid levels

Key design features for tank suction service (both types)

  • Materials – Casing / column: carbon steel (coated) for clean products; stainless steel or duplex for corrosive chemicals. Impeller: bronze, 316SS, or 12% chrome. Shaft: stainless or alloy steel.

  • Column length – Customised to tank height (from top flange to lowest suction level).

  • Suction bell – Designed to minimise hydraulic losses and provide smooth flow into impeller.

  • Impeller – Mixed flow or radial flow, usually semi‑open or open if solids present.

  • Sealing – At discharge head (above tank), a mechanical seal or packing is used to prevent leakage out of the column. Plan 11 (recirculation) or Plan 01 (packing).

  • Discharge head – Contains bearing housing (oil or grease) and motor support.

  • Motor – Vertical hollow shaft motor (preferred) or solid shaft with coupling.

  • Anti‑rotation device – Prevents column from rotating during start/stop.

  • Flushing connections – For cleaning or heating (if product solidifies).

Why choose our API 610 tank suction pumps?

  • Full API 610 compliance – VS4/VS5 types verified per standard. Performance test, mechanical run test.

  • Optimized suction hydraulics – Low NPSH, smooth inlet flow.

  • Custom column length – Exactly matched to your tank geometry.

  • Easy maintenance – Top‑pull design (both types) allows withdrawal without tank draining.

  • Short lead time – Standard lengths available; custom 10‑14 weeks.

  • Global spare parts support – Columns, shafts, bearings, impellers, discharge heads shipped worldwide.

Quality assurance

  • ISO 9001:2015 certified.

  • API 610 mechanical run test (4 hours) with vibration monitoring.

  • Hydrostatic test of discharge head and column (if specified).

  • Material traceability EN 10204 3.1 / 3.2.

How to specify your tank suction pump

Please provide: flow (m³/h), head (m), liquid type (water, chemical, crude, product), temperature (°C), tank depth (distance from top flange to minimum liquid level), NPSHa (m), solids content (if any), and required material (carbon steel / 316SS / duplex). We will recommend VS4 or VS5 type, column length, impeller material, bearing type (for VS5), and seal/packing.

Contact us

For a quotation or technical discussion on tank suction pumps (API 610 VS4 / VS5) :

info@hyrig.com


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit