A recycle pump (also called reactor recycle pump) circulates high‑pressure liquid within a process loop – most commonly in hydrocrackers, desulfurization reactors, or other fixed‑bed catalytic hydroprocesses. The pump takes high‑pressure effluent from the reactor and recycles it back to the inlet, mixed with fresh feed. This service demands very high discharge pressure (up to 250 bar), high temperature (up to 400°C), and continuous reliability because pump failure means immediate unit shutdown. Our API 610 BB2 multistage, axially split, between‑bearings pump is specifically engineered for such severe recycle duty. This design fully complies with API 610 11th/12th edition (ISO 13709) .
Structure match check: API 610 BB2 is defined as a horizontal, axially split, multistage, between‑bearings pump with centerline support for high temperature. This matches recycle pump requirements because:
Recycle pumps often require heads from 200 to 1500 m (depending on loop pressure drop). Multistage BB2 achieves this without resorting to expensive barrel pump (BB5) unless pressure exceeds about 220 bar – though BB2 can handle up to 250 bar with heavy wall design.
Axially split casing allows full internal inspection and maintenance (impellers, diffusers, wear rings) without disturbing piping – critical for minimal downtime.
Centerline support accommodates thermal expansion at up to 400°C.
Between‑bearings rotor provides stability at high speeds and high radial loads.
Opposed impeller orientation naturally balances axial thrust, eliminating a balance drum (which can wear in heavy oil service).
Why API 610 BB2 for recycle pump duty?
Very high pressure capability – Designed for discharge pressures up to 250 bar (3600 psi), the upper limit for axially split casing. For higher pressures (e.g., 350 bar), BB5 barrel pump would be required. BB2 is cost‑effective for most hydrocracker recycle duties.
High temperature – Reactor recycle liquid is typically 300‑400°C. WC6 casing (1¼Cr-½Mo), centerline support, water‑cooled bearing housings, and Plan 23 seals (cooled recirculation) ensure long life.
Hydraulic thrust balance – Opposed impeller configuration (back‑to‑back) eliminates axial thrust without a balance drum, reducing maintenance and improving reliability for heavy, dirty recycle oil.
Abrasion resistance – Recycle oil may contain catalyst fines or coke particles (especially from hydrocracker). Hardened 12% chrome (CA6NM) or 17-4PH impellers and Stellite wear rings provide erosion protection.
High efficiency – Multistage design achieves 80‑86% efficiency at design point, saving significant energy on a pump that runs 24/7.
Ease of maintenance – Fully accessible by removing top casing half; stage parts, bearings, and seals can be serviced without pulling the rotor from the piping.
Key design features for recycle service
Casing – Axially split, centerline support. Material: WC6 or WC9 for up to 450°C. Pressure rating: ASME Class 900 or 1500. Flanged connections suitable for high pressure.
Impellers – Opposed arrangement (back‑to‑back) balances thrust hydraulically. First stage often double‑suction to reduce NPSHr. Hardened CA6NM (12% chrome) or 17-4PH. Replaceable Stellite or hardened 17-4PH wear rings.
Diffusers – Stationary vanes in hardened stainless steel.
Shaft – Large diameter, short span. Material: 12% chrome or 17-4PH. Replaceable shaft sleeves under seals.
Bearings – Tilting pad journal bearings for high speed and load; double‑acting Kingsbury thrust bearing. Pure oil mist lubrication standard. Bearing housings water‑cooled (coils) due to high ambient temperature from casing radiation.
Sealing – API 682 Plan 23 (cooled seal chamber recirculation) is mandatory for hot recycle (>250°C). Plan 32 (external cool flush) if clean liquid available. For hazardous (H₂S) or zero emission, double seals with Plan 53A. Seal faces: SiC vs. SiC.
NPSH – Recycle pump suction normally is high pressure (e.g., reactor outlet), so NPSH is rarely a concern. However, first stage double suction optional for conservative design.
Materials for sour service – Recycle loops often contain H₂S (hydrocracking). NACE MR0175 compliance required: Casing low‑temp carbon steel (LCC) or WC6 with proper hardness, and 12% chrome impellers with hardness <22 HRC.
Flushing / cooling circuits – Additional piping for warming before start‑up and cooling before shutdown.
Typical performance range
| Parameter | Value |
|---|---|
| Flow rate | 50 – 2000 m³/h |
| Head | 200 – 1500 m |
| Discharge pressure | Up to 250 bar |
| Temperature | Up to 400°C |
| Speeds | 1500 – 6000 rpm |
| Stages | 3 – 10 (opposed arrangement) |
Typical applications
Hydrocracker (HCU) reactor recycle pump – heavy VGO or resid.
Hydrodesulfurization (HDS) reactor recycle – gas oil or diesel.
Hydrotreating (HDT) recycle – naphtha, kerosene.
Chemical reactor recycle loops – similar high pressure, high temperature.
Coal liquefaction recycle pumps (severe wear service).
Why choose our API 610 BB2 recycle pump?
Full API 610 compliance – Type BB2 verified. Performance test, NPSH test, 4‑hour mechanical run test with vibration monitoring.
Opposed impeller design – no balance drum, no axial thrust wear, longer MTBR.
High temperature / high pressure – WC6 casing, Plan 23 seals, water‑cooled bearings.
Abrasion resistance – Hardened 12% chrome impellers and Stellite wear rings.
Easy maintenance – Axially split casing allows access without pipe removal.
Short lead time – Standard sizes with WC6 / 12% chrome available 32‑36 weeks.
Global spare parts support – Complete stage sets, impellers, diffusers, shafts, bearings, seal cartridges shipped worldwide.
Quality assurance
ISO 9001:2015 certified.
API 610 mechanical run test (minimum 4 hours) with vibration and bearing temperature monitoring.
Hydrostatic test of casing at 1.5× working pressure.
Material traceability EN 10204 3.1 / 3.2.
NDE – MT, PT, UT, RT as required.
Rotor dynamic analysis + lateral critical speed report.
How to specify your recycle pump
Please provide: flow (m³/h), head (m), operating temperature (°C), reactor pressure (bar), fluid composition (gas oil, VGO, resid, naphtha, etc.), solids content (catalyst fines, coke), H₂S content (for NACE), NPSHa (m), required material class (WC6 / LCC / duplex), and driver type. We will recommend number of stages (opposed), impeller design (first stage double‑suction if needed), seal plan (23/53A), bearing cooling, and driver details.
Contact us
For a quotation or technical discussion on recycle pumps (API 610 BB2) :
info@hyrig.com
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.