KHT5500 Hydraulic Power Tong – Wear Parts Maintenance Guide (Integrated with Troubleshooting Scenarios)

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
KHT5500 hydraulic power tong wear parts guide. Definition: parts subject to friction, pressure, corrosion – regular inspection and replacement required. Key wear parts by priority: jaws (6 sizes for master, 7 for backup, replace every 3-5 wells or wear >1mm), dies (11 sizes, replace after 2 jaw changes), hydraulic seals (O-rings, replace every 6-8 wells or at leak), brake staple (wear ≥3mm, replace every 4-6 wells), rollers & shafts (replace every 5-7 wells or sticking), gears (inspect at 10 wells, replace if pitting/breakage), hoses (replace every 12-15 wells or aging), safety door interlock valve (replace when failed). Stock management: keep 1-2 sets of critical parts, store in dry clean area. Use only TEDA OEM parts with correct codes. Contact info@hyrig.com.

Conatct For Details
DetailReview(0)Additional

Definition & Core Characteristics of Wear Parts

Wear parts are components that wear quickly due to friction, pressure, or media corrosion during normal operation, requiring regular inspection and replacement. For the TEDA KHT5500 Hydraulic Power Tong, wear parts directly affect operational safety and equipment stability. Replacement must follow the principle: regular inspection, replacement as needed, correct specification matching.


Key Wear Parts List (Ordered by Wear Priority)

#Wear PartSpecification / Part CodeReplacement Interval (reference)Replacement CriteriaSafety Requirements
1Jaws (Master & Backup)Master: 2.38″(60.3), 2.88″(73), 3.5″(88.9), 4.5″(114.3), 5″(127), 5.5″(139.7mm). Backup: adds 6.5″(165.1mm). Codes: KHT5500-24/26/43-573-5 wells normal; 1-2 wells harsh① Tooth wear depth ≥1mm
② Teeth clogged permanently
③ Deformation/cracks
④ Slipping during gripping
Shut down hydraulic power, release pressure. Ensure correct jaw positioning (front two master jaws interchangeable; rear jaw has roller). Tighten bolts to 25-30 N·m (1/2″ bolt).
2Dies11 sizes: 7/16″-1″, 1-1/16″. Code: KHT5500-32 seriesAfter every 2 jaw changes① Surface wear, deep scratches
② Anti-slip texture lost
③ Loose or missing bolts
Clean oil from jaw/die contact surface before removal. Ensure tight fit. Do not mix different die sizes – uneven grip force.
3Hydraulic Seals (torque cylinder, motor, valve)For NPT 1″/1-1/4″ ports. O-ring sizes: 22.4×2.65, 35×3.1, 45×3.1 etc. Codes: KHT5500-189/221/2616-8 wells or when leakage occurs① Oil leak (oil traces on fitting or cylinder body)
② Rapid pressure drop
③ Deformation, aging, cracks
Fully depressurize before replacement. Clean seal groove with clean cloth. Use OEM seals only – no non-standard. Apply hydraulic oil for lubrication during installation to avoid cuts.
4Brake StapleCode: KHT5500-664-6 wells or brake failure① Wear ≥3mm
② Loose, cannot lock
③ Brake torque <80% of rated
Check brake spring at same time (code KHT5500-80). Test brake function after installation – confirm reliable jaw lock. Do not hammer staple – may deform and affect braking.
5Rollers & Roller Shafts (jaws, gearbox)Roller code: KHT5500-49; Shaft code: KHT5500-515-7 wells or when sticking noise heard① Roller rotates roughly or sticks
② Shaft worn or rusted
③ Roller surface uneven
Avoid hammering during removal to prevent bushing damage. Add lithium grease after installation. Ensure roller aligns with contact surface.
6Gears (transmission, meshing)Small intermediate gear (KHT5500-110), large intermediate gear (KHT5500-111), large gear (KHT5500-117)Inspect at 10 wells; replace if severe wear① Tooth surface wear, pitting, broken teeth
② Unusual noise or vibration during meshing
③ Difficulty shifting gears
Requires trained technician for gearbox disassembly. Calibrate gear backlash (0.15-0.3mm) after replacement. Fill with专用 gear oil, run no-load for 30 minutes.
7Hydraulic Hoses (pressure / return)Pressure: KHT5500-191A/192A; Return: KHT5500-201/215 (custom length)12-15 wells or when aging① Surface cracking, bulges
② Fitting leaks
③ Hose deformed, pressure resistance reduced
Match port sizes (NPT1″ pressure, NPT1-1/4″ return). Do not kink hoses – keep straight runs. Pressure test after replacement (14 MPa, hold 5 min with no leaks).
8Safety Door Interlock Valve Components (spool, spring)Valve code: KHT5500-224; Spring code: KHT5500-165/175When interlock fails① Spool sticking or worn
② Spring deformed, weak
③ Door interlock fails (door open but power not cut)
Depressurize before disassembly. Clean valve body debris. Ensure spool moves freely after installation. Test interlock function – door open = power cut, door closed = power on.

Wear Parts Management Requirements

Stock Management

  • Critical wear parts (jaws, seals, dies): keep 1-2 sets as spares based on operation volume – enables quick replacement during sudden failures.

  • Storage environment: Clean, dry. Apply grease on jaws and dies for rust prevention. Keep hoses away from direct sunlight to prevent aging.

Replacement Log

  • Maintain a wear parts replacement log recording: date, number of wells since last change, reason for replacement, operator name.

  • Also record operating parameters (pressure, torque, speed) to support optimization of replacement intervals.

Procurement Requirements

  • Must use TEDA genuine wear parts (reference part codes). Do not use non-standard or substitute parts – risk of equipment damage or safety incidents.

  • When ordering, specify equipment model (KHT5500) and exact part specification for accurate fit.

Disposal of Used Parts

  • Classify and recycle used wear parts (seals, hoses, etc.). Parts contaminated with hydraulic oil must be cleaned before disposal. Do not discard arbitrarily to avoid environmental pollution.


Maintenance Note

The replacement intervals above are reference values. Actual intervals depend on operating conditions (pipe hardness, operation intensity, environmental humidity). Always combine with troubleshooting findings – stop and replace immediately if any abnormality is detected. Do not let minor faults escalate into major equipment overhauls.


Contact Us

For genuine wear parts orders, technical advice, or to request a custom stocking plan, please contact us:

info@hyrig.com

We provide complete spare parts support for all TEDA power tongs, including the KHT5500.


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit