Definition: Components that wear or age quickly due to frequent friction, stress, or environmental corrosion during operation. Failure to replace them in time can cause equipment failure, reduced efficiency, or safety incidents.
Identification Principles:
High-frequency contact parts: Direct contact with casing, hydraulic oil, gears (e.g., jaws, seals)
Stress-bearing parts: Subject to torque, pressure, impact (e.g., locating pins, brake belt)
Environment-sensitive parts: Affected by temperature, humidity, corrosive media (e.g., hydraulic hoses, grease)
Visual Criteria for Replacement: Wear, cracks, deformation, aging, leakage, functional failure – replace immediately.
| Part Name | Specifications | Replacement Interval (reference) | Visual Criteria | Function |
|---|---|---|---|---|
| Jaws | For 7″-20″ casing (10 sizes), precision cast | Every 300 hrs or wear >1 mm | Roller wear/crack, jaw deformation, loose bolts | Directly grip casing for make-up/break-out |
| Jaw rollers | Matching jaws, wear-resistant alloy | Every 200 hrs or rotation sticking | Surface wear, cracks, rough rotation | Reduce friction, ensure smooth clamping |
| Locating pins | OEM custom size, high-strength steel | Every 150 hrs or bent/rusted | Breakage, deformation, difficult insertion, rust | Fix tong position during operation |
| Brake belt | Matches cage plate size, rubber + metal | Every 500 hrs or gap >0.5 mm | Surface wear, cracks, poor cage plate contact | Provide friction for jaw clamping |
| Door lock cam | OEM size, high-strength wear-resistant | Every 400 hrs or locking failure | Surface wear, sticking, door won't lock | Control safety door locking |
| Door stop spring | Matching safety door, specified spring rate | Every 300 hrs or loss of elasticity | Deformation, breakage, door won't stay closed | Assist door locking, cushion impact |
| Part Name | Specifications | Replacement Interval | Visual Criteria | Function |
|---|---|---|---|---|
| Hydraulic hoses | Pressure hose 1″, return hose 1-1/4″, 18 MPa rating | Every 1000 hrs or aging/cracking | Bulges, cracks, leaks, loose fittings | Transmit hydraulic power |
| Hydraulic seals | For fittings, tank, valves; oil-resistant rubber | Every 500 hrs or leakage | Deformation, aging, damaged sealing surface | Prevent oil leaks, maintain pressure |
| Hydraulic filter | For tank, filtration ≥25μm | Every 200 hrs or clogging | Excessive debris, poor oil flow | Filter contaminants, protect pump/valves |
| Relief valve spool | OEM precision machined | Every 800 hrs or pressure instability | Sticking, wear, unstable system pressure | Regulate pressure, prevent overpressure |
| Part Name | Specifications | Replacement Interval | Visual Criteria | Function |
|---|---|---|---|---|
| Torque gauge | Range 0-60,000 ft·lb, ±2% accuracy | Every 12 months or inaccurate | No display, error >±2%, pointer sticking | Monitor torque, ensure thread quality |
| Grease | Multi-purpose bearing grease, -40°C to 60°C | Top up after each use; full change every 500 hrs | Deteriorated, solidified, contaminated | Lubricate core components, reduce wear |
| Hydraulic oil | OEM specified (ISO VG46 for high temp, VG32 for low temp) | Every 2000 hrs or oil degradation | Dark color, emulsified, excessive debris | Power transmission medium, cooling, lubrication |
| Fuses | Rated for electrical system | Replace when blown | Melted, equipment won't power on | Protect electrical components from overload |
Before replacement: Cut power and hydraulic supply. Hang "Parts Replacement – Do Not Operate" tag. Wear PPE.
Tools ready: Appropriate wrenches, screwdrivers, grease gun, cleaning cloth, genuine spare parts.
Procedure: Remove → Clean → Install → Test. Mark parts during removal to avoid misalignment.
Test: Run no-load for 5 minutes. Check function, leaks, unusual noise. Then resume loaded operation.
Jaw Replacement:
Remove jaw pivot bolt from cage plate using wrench.
Clean cage plate mounting surface with cloth (remove oil and debris).
Place new jaw (correct size for casing) between upper and lower cage plates with roller pin facing up. Align holes, insert pivot bolt, tighten.
Test: Manually rotate tong body – jaw action smooth, no sticking.
Hydraulic Hose Replacement:
Depressurize: Close hydraulic supply, open bypass valve.
Remove old hose fittings (mark connection positions to avoid errors).
Clean fitting ports.
Install new hose per marks. Fully engage fittings – self-sealing couplers must click locked.
Test: Run no-load, check for leaks and stable pressure.
Locating Pin Replacement:
Remove old pin with tool (apply rust penetrant if stuck).
Clean mounting hole (remove rust and debris).
Insert new pin, tap gently until fully seated.
Test: Insert/remove pin – smooth, no sticking. No looseness during operation.
Hydraulic Filter Replacement:
Close tank valve, remove filter housing, take out old filter.
Clean filter mounting seat.
Insert new filter, tighten housing (ensure good seal).
Test: Open tank valve, run unit to circulate oil. Check for leaks and normal oil flow.
Official channel: Contact Yancheng TEDA directly (hotline: +86 19905158858) or website (www.chinateda.com). 100% OEM parts, full compatibility.
Authorized distributors: Purchase through factory-authorized regional distributors – same quality and service.
Prohibited: Never use non-OEM parts (non-standard hoses, poor-quality seals). Risk of equipment failure and safety incidents.
| Operation Scale | Essential Stock Items | Recommended Quantity |
|---|---|---|
| Single unit, daily operation | Jaws (2 sets of common size), locating pins (3), seal kit (1), hydraulic filters (2), grease (5 kg) | Quarterly replenishment |
| Multi-unit, large-scale operation | Jaws (1 set each size), hoses (pressure & return, 2 each), brake belts (2), door lock cams (2), filters (5), hydraulic oil (20 L) | Monthly restock, regular inventory |
| Remote area operation | Add relief valve spool (1), torque gauge (1), door stop springs (5) to large-scale stock | Semi-annual stock, for emergency |
Environment: Clean, dry, ventilated. Away from heat, moisture, corrosive sources. Prevent rust and aging.
Storage method: Categorize and label parts with specifications and replacement intervals. Store tools together.
Shelf life management: For hydraulic oil, grease, etc., store by production date; use older stock first.
Genuine guarantee: All OEM wear parts are 100% factory-tested, fully compatible. Warranty: seals, filters (3 months); jaws, hoses (6 months).
Fast delivery: 20+ service centers nationwide. Common wear parts in stock. Emergency orders delivered within 48 hours (72 hours for remote areas).
Replacement training: Free on-site or online training for wear parts replacement – teach maintenance personnel standard procedures.
Custom stocking plan: Tailored wear parts list based on your operation scale, location, and working conditions – reduce inventory costs.
Upgrade service: TEDA continuously improves part materials. Existing customers receive upgrade discounts to extend part life.
For genuine wear parts orders, technical advice, or to request a custom stocking plan, please contact us:
info@hyrig.com
We provide complete spare parts support for all TEDA casing power tongs, including the KT20000
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.