OH2 Pump Advantages – Why API 610 OH2 Outperforms OH1 & BB1 for High Temperature Service

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
OH2 pump is API 610 overhung centerline mounted pump, designed for high temperature service where foot-mounted OH1 cannot work stably. Core advantages: centerline mounted eliminates thermal deformation at high temperature (up to 425°C); back pull-out enables maintenance without removing pipes; higher temperature resistance than OH1; compact overhung structure offers lower cost than BB pumps; stable 24/7 continuous process duty. OH2 vs OH1: OH1 foot-mounted for normal temperature (≤250°C), OH2 centerline-mounted for high temperature (≤425°C). OH2 vs BB1: OH2 overhung simpler, cost-effective; BB1 between bearings for larger flow and higher pressure. Suitable for high temperature process, hot oil system, refinery and petrochemical critical auxiliary pump.

Conatct For Details
DetailReview(0)Additional

The OH2 pump is an API 610 horizontal single-stage overhung centrifugal pump with centerline mounted design. It is specifically engineered for high temperature service where foot-mounted OH1 pumps cannot operate stably. Compared to between-bearings BB1 pumps, the OH2 offers a more compact, cost-effective solution for medium pressure, high temperature duties.

Core Advantages of OH2 Pump

  • Centerline Mounted Design → No Thermal Deformation at High Temperature
    Casing feet are at the shaft centerline, allowing even thermal expansion. Unlike foot-mounted pumps, the OH2 will not tilt or bind when handling fluids up to 425°C (797°F). This eliminates misalignment, reduces bearing and seal wear, and ensures stable operation.

  • Back Pull-Out Structure → Easy Maintenance Without Removing Pipes
    The entire rotating assembly (impeller, shaft, bearing housing, seal) can be removed from the rear while the casing and piping remain in place. For hot oil or high-temperature hydrocarbon services, this means safer, faster maintenance with minimal downtime.

  • Higher Temperature Resistance Than OH1

    • OH1: Foot-mounted, suitable for normal temperature up to 250°C (482°F) – higher with cooling jacket

    • OH2: Centerline-mounted, designed for high temperature up to 425°C (797°F) without special cooling

  • Compact Overhung Structure → Lower Cost Than BB Type Pumps
    OH2 pumps are single-stage overhung, meaning fewer bearings, simpler casting, and smaller footprint than between-bearings BB1 pumps. For medium pressure (≤30 bar), medium flow, and high temperature duties, the OH2 provides the best balance of reliability and cost.

  • Stable Operation for 24/7 Continuous Process Duty
    Heavy-duty bearing housing, API 682 mechanical seals with appropriate flush plans (Plan 21, 23, 31), and robust shaft design ensure years of continuous operation in refinery and petrochemical services.

OH2 vs OH1 (Foot-Mounted Overhung Pump)

FeatureOH2 (Centerline Mounted)OH1 (Foot Mounted)
MountingCenterline (feet at shaft center)Foot (casing bottom)
Temperature rangeUp to 425°C (797°F) – ideal for hot serviceUp to 250°C (482°F) – higher requires cooling
Thermal expansionEven around centerline, no misalignmentCasing expands upward, may cause misalignment
Best applicationHot oil, high temp hydrocarbons, thermal fluidsGeneral process, cooling water, moderate temp
CostSlightly higher (more complex casting)Lower

Verdict: Use OH2 when operating temperature exceeds 200°C continuously. Use OH1 for general service below 200°C where cost is the primary driver.

OH2 vs BB1 (Axial Split Between Bearings Pump)

FeatureOH2BB1
ConfigurationOverhung (single bearing housing)Between bearings (two bearing housings)
Pressure capabilityUp to 30 bar (435 psi)Up to 40 bar (580 psi)
Flow rangeSmall to medium (up to 2,200 m³/h)Medium to large (up to 2,800 m³/h)
TemperatureUp to 425°C (centerline mount)Up to 400°C (centerline mount available)
CompactnessVery compact, smaller footprintLarger, requires more space
CostLower (simpler construction, fewer parts)Higher
MaintenanceBack pull-out – very fastAxial split – open upper half
Best forHigh temperature, medium pressure, cost-sensitiveLarger flow, higher pressure, where between-bearings stability is required

Verdict: Choose OH2 for high temperature duties at moderate flow and pressure where cost and footprint matter. Choose BB1 for larger flows, higher pressures, or when you specifically need a between-bearings design for long-term critical service.

Suitable Working Conditions

  • High temperature process (200°C to 425°C)

  • Hot oil circulation systems (thermal oil heaters)

  • Refinery high temperature transfer (fractionator bottoms, heavy gas oil)

  • Petrochemical high temperature media (quench oil, heat transfer fluids)

  • Power plant high temperature condensate and auxiliary water

  • Chemical corrosive high temperature liquids (with 316L or duplex)

Get an OH2 Pump vs OH1 / BB1 Comparison for Your Duty

Our engineering team provides free pump selection advisory. Send us your duty point:

  • Flow rate (m³/h or GPM)

  • Total head (m or ft)

  • Operating temperature (°C)

  • Fluid (and any corrosivity)

  • Pressure requirement

We will reply within 24 hours with:

  • Recommended pump type (OH2, OH1, or BB1)

  • Side-by-side comparison for your specific duty

  • Performance curve and API data sheet

  • CAD drawing (2D) and 3D model

  • Factory direct price (EXW / FOB / CIF)

Email: info@hyrig.com

We are a professional API 610 pump manufacturer (OH1, OH2, BB1, BB2, BB3, BB4, BB5, VS types) serving global refineries, petrochemical plants, hot oil systems, and high-temperature industries. Contact us for custom-engineered OH2 pumps at factory direct wholesale pricing.


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit