This page provides complete technical parameters for our OH2 API 610 horizontal single-stage overhung centrifugal pump with centerline mounted design. The OH2 is specifically engineered for high temperature service up to 425°C, making it the preferred choice for hot oil circulation, refinery high-temperature process transfer, and petrochemical high-temperature media handling.
Performance Range
| Parameter | Value |
|---|---|
| Flow rate | 5 ~ 2,200 m³/h (22 ~ 9,700 GPM) |
| Total head | 10 ~ 320 m (33 ~ 1,050 ft) |
| Speed | 1480 / 2980 rpm (50/60 Hz) |
| Medium temperature | -40°C ~ +425°C (-40°F ~ +797°F) |
| Maximum working pressure | Up to 30 bar (435 psi) – higher on request |
| NPSHr | Low NPSH optimized hydraulic design – inducer optional |
Structural & Mechanical Design
Type: Horizontal single-stage overhung (API 610 OH2 designation)
Mounting: Centerline mounted – casing feet at shaft centerline for even thermal expansion at high temperature, preventing misalignment and seal distress
Casing: Radial split, end suction / top discharge – back pull-out design allows rotating assembly removal without disconnecting piping
Impeller: Closed (standard for clean high-temp fluids) or semi-open (for slight solids) – single suction
Bearing housing: Heavy-duty oil lubricated (splash or forced feed) – designed for high temperature operation
Seal: API 682 cartridge mechanical seal – supports all plans (Plan 21, 23, 31, 52, 53, etc. for hot service)
Material Selection
| Component | Standard Materials | Upgrade Options |
|---|---|---|
| Casing | Carbon steel (WCB), 316L stainless steel | Duplex, super duplex, alloy steel |
| Impeller | Stainless steel (316L), high alloy (17-4PH) | Duplex, high-chrome |
| Shaft | Forged alloy steel (high temperature resistance, 4140/420) | Duplex, K500 |
| Wear rings / bushings | Replaceable anti-corrosion alloy | Colmonoy-coated, Stellite |
Key Design Features Explained
Centerline Mounting for High Temperature
Unlike foot-mounted OH1 pumps, the OH2's centerline support allows the casing to expand evenly around the shaft centerline. This eliminates thermal misalignment, binding, and seal/bearing failures common in hot service. The OH2 is the correct choice for continuous operation above 200°C.
Back Pull-Out Maintenance
The complete rotating assembly (impeller, shaft, bearing housing, seal) can be pulled out from the rear without disturbing suction or discharge piping. For hot oil services, this means bearings and seals can be replaced while piping remains in place – reducing downtime dramatically.
API 682 Sealing for High Temperature
For high temperature applications, we recommend API 682 Plan 23 (jacketed seal with pumped circulation) or Plan 21 (cooled flush from discharge). Dual seals (Plan 52/53) are available for hazardous or volatile high-temperature fluids.
Low NPSH Design
The OH2 hydraulic profile is optimized for low NPSH requirements, critical when pumping hot liquids near their vapor pressure. Optional inducer can further reduce NPSHr.
Available Technical Documents (Free Request)
API 610 data sheet (fully filled with your operating conditions)
Installation dimension drawing (2D CAD, PDF/DWG) – includes footprint, nozzle coordinates, centerline height
Performance curve (head, efficiency, NPSHr vs flow with multiple impeller trims)
3D model (STEP/IGES for plant integration)
Material certificate (EN 10204 3.1 or 3.2)
Hydrostatic test and performance test report
Typical High Temperature Applications
Hot oil circulation – Thermal oil heaters up to 400°C, heat transfer fluid loops
Refinery process – Fractionator bottoms, heavy gas oil, vacuum residue transfer
Petrochemical – Quench oil, high temperature solvents, MEG regeneration
Power plant auxiliary – High temperature water circulation, heat recovery systems
Chemical – Hot acid transfer, high temperature process fluids
Get Your OH2 Pump Technical Specification Package
To request a complete documentation package with a formal quotation, please send us your operating conditions:
Flow rate (m³/h or GPM)
Total head (m or ft)
Fluid name and temperature (°C)
Operating pressure (bar)
Any special requirement (material, seal plan, inducer, ATEX, etc.)
Our engineering team will respond within 24 hours with:
Recommended OH2 pump model (size, impeller trim, material)
Performance curve PDF
API 610 data sheet
2D CAD drawing and 3D model link
Seal and flush plan recommendation for high temperature
Factory direct price (EXW / FOB / CIF)
Email: info@hyrig.com
We are a professional API 610 pump manufacturer (OH1, OH2, BB1, BB2, BB3, BB4, BB5, VS types) serving global refineries, petrochemical plants, hot oil systems, and high-temperature process industries. Contact us for custom-engineered OH2 pumps at factory direct wholesale pricing.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.