Produced Water Pump | API 610 OH2 Centrifugal Pump | China OH2 Pump Manufacturer

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
API 610 OH2 single‑stage, overhung pump for produced water (oilfield produced water containing oil, brine, sand, and H₂S). Corrosion resistant duplex / 316SS with hardened trim for abrasion. Low NPSH design. Suitable for onshore & offshore produced water transfer. China OH2 pump manufacturer.

Conatct For Details
DetailReview(0)Additional

A produced water pump handles water that is brought to the surface along with oil and gas. Produced water is typically a complex mixture of brine (high chlorides), residual oil (free and emulsified), sand or silt, and often contains H₂S, CO₂, and scale‑forming compounds. This fluid is highly corrosive, erosive, and often has low net positive suction head (NPSH) from separator vessels or skim tanks. Our API 610 OH2 centrifugal pump is specifically engineered for reliable, long‑life produced water transfer in onshore oilfields, offshore platforms, and water treatment facilities. This design fully complies with API 610 11th/12th edition (ISO 13709) .

Structure match check: API 610 OH2 is defined as a horizontal, single‑stage, overhung pump with foot‑mounted casing and back pull‑out design. This matches produced water service requirements because:

  • OH2 provides easy maintenance – back pull‑out for seal, impeller, wear parts without disturbing piping – essential for abrasive/corrosive service that requires frequent inspection.

  • Many produced water duties require intermediate heads (up to 200 m) and moderate flows (10-1000 m³/h), which fits OH2 hydraulic coverage.

  • Corrosion and erosion resistant alloys (duplex, super duplex, 316SS with hardened trim) can be fully implemented.

  • Low NPSH can be achieved with inducer or double‑suction first stage, important for suction from three‑phase separators or skim tanks with low liquid levels.

Why API 610 OH2 for produced water duty?

  • Corrosion resistance – High chloride brine, H₂S, and CO₂ demand duplex (2205) or super duplex (S32750) wetted parts. For less aggressive water, 316SS may be acceptable. NACE MR0175 compliance for H₂S service is standard.

  • Erosion resistance – Sand and silt cause rapid wear on impellers, wear rings, and casing. Hardened 17-4PH or Stellite overlays on wear parts. Optional semi‑open impeller with replaceable wear plate.

  • Low NPSH – Produced water vessels (separators, flotation units, tanks) often provide less than 2 m NPSHa. Inducer standard to reduce NPSHr below 1 m, preventing cavitation that accelerates wear.

  • Solids handling – Open or semi‑open impeller (up to 10 mm particle passage) for sandy produced water. Replaceable wear plate protects casing.

  • Sealing for dirty, corrosive service – API 682 Plan 31 (cyclone separator) recirculates clean fluid from discharge to seal. Plan 32 (external clean water flush) dilutes brine and removes solids from seal face. Double seals with Plan 53A for zero H₂S emissions.

  • Continuous duty – Produced water pumps often run 24/7. API 610 bearings, oil mist option, and heavy‑duty shaft ensure high MTBR.

Key design features for produced water service

  • Materials – Casing: duplex (CD4MCu) or super duplex (S32760) for most brine/H₂S service. Impeller: duplex or 17-4PH with hardened surface. Shaft: duplex or 17-4PH. Wear rings: Stellite overlay or 17-4PH H1150. Gaskets: PTFE. Fasteners: Alloy 20 or Hastelloy for corrosion under insulation (CUI) protection.

  • Impeller type – Closed for low solids; semi‑open with replaceable wear plate for sand up to 5-10 mm. Open impeller for very high solids.

  • Inducer – Highly recommended for NPSHa below 3 m.

  • Sealing – Cartridge mechanical seal. Plan 31 (cyclone cleaner) to remove solids before seal chamber. Plan 32 (external clean water) for continuous flush if available. For H₂S, double seal with Plan 53A (pressurized barrier fluid) and leak detection.

  • Bearing housing – Oil lubricated, with purged labyrinths to prevent brine ingress. Pure oil mist recommended for continuous remote service.

  • Casing drain – Full size for flushing settled solids during maintenance.

  • Coating – Internal epoxy coating on non‑wetted carbon steel parts (baseplate, guard) for additional corrosion protection.

Typical performance range

ParameterValue
Flow rate10 – 1200 m³/h
HeadUp to 200 m
Temperature10°C – 90°C
Pressure ratingUp to 25 bar
NPSHr (with inducer)As low as 0.5 m
Solids passage (semi‑open)Up to 10 mm
Speeds1450 / 2900 / 3600 rpm

Typical applications

  • Onshore oilfield – Water from three‑phase separators to water treatment or reinjection.

  • Offshore platforms – Produced water transfer from skim tanks to overboard discharge or reinjection.

  • Heavy oil recovery – Water from oil/water separation units.

  • Refinery oily water systems – API separator effluent pumping.

  • Coal bed methane (CBM) – Produced water handling.

Why choose our API 610 OH2 produced water pump?

  • Full API 610 compliance – Performance test, NPSH test (inducer), 4‑hour mechanical run test with vibration monitoring.

  • Corrosion + erosion resistant materials – Duplex or super duplex with hardened wear surfaces extend pump life in aggressive produced water.

  • Low NPSH – Inducer ensures cavitation‑free operation from low‑level separators.

  • Easy solids removal – Semi‑open impeller and replaceable wear plate; large casing drain.

  • Short lead time – Standard duplex pumps with inducer available 12‑14 weeks.

  • Global spare parts support – Impellers, wear plates, wear rings, shafts, seal cartridges, bearings shipped worldwide.

Quality assurance

  • ISO 9001:2015 certified.

  • API 610 mechanical run test (4 hours) with vibration and bearing temperature monitoring.

  • NPSH test verification (inducer).

  • Hydrostatic test of casing.

  • Material traceability EN 10204 3.1 / 3.2.

  • PMI for all alloy components.

  • NDE – MT, PT, UT as required.

How to specify your produced water pump

Please provide: flow (m³/h), head (m), temperature (°C), NPSHa (m), salinity (chloride ppm), H₂S content (ppm), sand content and size (µm or mm), oil content (ppm), required material (316SS / duplex / super duplex), and preferred seal plan. We will recommend inducer (yes/no), impeller type (closed/semi‑open), seal plan (31/32/53A), material grade, and driver details.

Contact us

For a quotation or technical discussion on produced water pumps (API 610 OH2) :

info@hyrig.com


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit