A waste water pump handles industrial effluent, sewage, plant runoff, and process drainage. Waste water may be corrosive (low/high pH), contain abrasive solids (sand, scale), have variable composition (oily, chemical, biological), and often requires pumping from sumps or pits with low net positive suction head (NPSH). Our API 610 OH2 and VS4 pumps are specifically engineered for reliable waste water service in refineries, chemical plants, power stations, and municipal treatment. Both designs fully comply with API 610 11th/12th edition (ISO 13709) .
API 610 OH2 – Horizontal Waste Water Pump
Structure match check: API 610 OH2 is defined as a horizontal, single‑stage, overhung pump with foot‑mounted casing and back pull‑out design. This is suitable for above‑ground waste water transfer where suction is from a wet well with positive head, or from a pump station with adequate NPSH.
Why OH2 for waste water?
Compact, economical for flow 5 to 1500 m³/h, head up to 150 m.
Back pull‑out maintenance – seal, impeller, bearings accessible without disturbing piping.
Solids handling – open or semi‑open impeller (up to 10-20 mm particle passage). Replaceable wear plate protects casing.
Corrosion resistant materials – 316SS, duplex, or cast iron with epoxy coating.
Low NPSH – inducer option for low NPSHa conditions.
Typical applications: lift stations, treatment plant interstage transfer, effluent discharge.
API 610 VS4 – Vertical Waste Water Pump
Structure match check: API 610 VS4 is defined as a vertical, single‑casing, rigid shaft, suspended pump with discharge head above the pit cover. This is ideal for pumping directly from sumps, pits, or wet wells where suction lift is required or space is limited.
Why VS4 for waste water?
Flooded or suction lift configuration – impeller submerged in pit, motor at grade.
Small footprint – pumps fits into a narrow pit or sump.
Solids handling – open impeller with large clearances (up to 25 mm particles).
No priming needed – impeller always submerged.
Easy maintenance – entire pump pulls vertically without dewatering the pit.
Flow range – 10 to 5000 m³/h, head up to 100 m.
Typical applications: sump drainage, clarifier underflow, sludge transfer, pit dewatering.
Comparison & Selection Guide
| Feature | OH2 (Horizontal) | VS4 (Vertical) |
|---|---|---|
| API 610 type | OH2 – overhung, foot‑mounted | VS4 – vertical suspended, rigid shaft |
| Installation | Above ground, baseplate | In pit / wet well / sump |
| Suction | Requires flooded suction or short lift | Submerged impeller – can handle suction lift |
| NPSH requirement | Moderate (inducer optional) | Very low/submerged – no cavitation |
| Footprint | Larger (horizontal length) | Small (vertical column) |
| Solids size | Up to 10-20 mm (open impeller) | Up to 25-50 mm (open impeller) |
| Flow range | 5 – 1500 m³/h | 10 – 5000 m³/h |
| Head range | Up to 150 m | Up to 100 m |
| Best for | Above‑ground, moderate solids | Pit/sump, large solids, low NPSH |
Key design features for waste water service (both types)
Material selection – For mildly corrosive waste water (pH 6-8, low chlorides): cast iron with high‑build epoxy coating. For aggressive waste water (pH <5 or >9, chlorides, H₂S): 316SS or duplex (2205). For highly abrasive waste water: hardened 17-4PH impeller, Stellite wear rings.
Impeller design – Open or semi‑open for solids passage. Replaceable front wear plate (OH2) or suction plate (VS4). Minimum clearances to prevent clogging.
Solids handling – Large internal flow passages. Impeller vanes designed to pass spherical solids up to specific diameter (e.g., 25mm, 50mm). For stringy materials (rags, fibers), non‑clog impeller with back sweep vanes.
Sealing – For clean to mildly dirty: Plan 11 (recirculation) with large seal gap. For abrasive or corrosive: Plan 32 (external clean water flush) to protect seal faces. For zero emissions (volatile waste): double seals with Plan 53A. Gland packing is also acceptable for low‑cost, intermittent duty.
Bearing housing – Heavy duty with oil bath. For wet pit or humid environment, purged labyrinth seals prevent moisture ingress. For continuous duty, oil mist optional.
VS4 specific – Often line‑shaft bearings: product lubricated rubber bearings (compatible with waste water). Grease‑lubricated intermediate bearings for deep pits (over 6 m). Column pipe materials: carbon steel with epoxy coating, or stainless steel.
Casing drain – Full size (2" or larger) for flushing settled solids.
Why choose our API 610 waste water pumps?
Full API 610 compliance – OH2 and VS4 types verified. Performance testing, mechanical run test.
Solids handling expertise – Open impellers, large passages, non‑clog designs for your specific particle size and type (sand, sludge, rags).
Corrosion protection – Cast iron with epoxy coating, or full stainless steel/duplex for aggressive effluents.
Low NPSH capability – OH2 inducer; VS4 flooded suction eliminates cavitation.
Easy maintenance – Back pull‑out (OH2) or vertical withdrawal (VS4) reduces downtime.
Short lead time – Standard cast iron OH2 pumps ex‑stock; VS4 and stainless versions 8‑12 weeks.
Global spare parts support – Impellers, wear plates, shafts, bearings, seals, column assemblies (VS4) shipped worldwide.
Quality assurance
ISO 9001:2015 certified.
API 610 mechanical run test (4 hours minimum) with vibration and bearing temperature monitoring.
Hydrostatic test of casing and column pipe.
Material traceability EN 10204 3.1 / 3.2.
NDE – MT, PT as required.
How to specify your waste water pump
Please provide: flow (m³/h), head (m), temperature (°C), NPSHa (m), waste water composition (pH, chlorides, H₂S, others), solids content and size (mm), presence of stringy materials (rags, fibers), installation type (above ground or pit/sump), pit depth (if VS4), and required material (cast iron coated / 316SS / duplex). We will recommend OH2 or VS4 type, impeller type (open/semi‑open/closed), seal plan (11/32/53A or packing), material class, and driver details.
Contact us
For a quotation or technical discussion on waste water pumps (API 610 OH2 or VS4) :
info@hyrig.com
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.