Condensate Extraction Pump | API 610 VS4 Vertical Pump | China VS4 Pump Manufacturer

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
API 610 VS4 vertical, single‑casing, rigid shaft pump for condensate extraction from steam turbine condensers / hotwell. Extremely low NPSH design, continuous duty. Suitable for power plants (fossil, nuclear, combined cycle). Corrosion resistant 316SS or bronze fitted. China VS4 pump manufacturer.

Conatct For Details
DetailReview(0)Additional

A condensate extraction pump (CEP) removes condensate from the steam turbine condenser hotwell (or surface condenser) and delivers it to the deaerator or downstream treatment. This pump must operate under very low net positive suction head (NPSH) because the condensate is near saturation temperature, often with only 1-2 meters of submergence. The API 610 VS4 vertical suspended pump is the industry standard for this demanding continuous duty. Our design fully complies with API 610 11th/12th edition (ISO 13709) .

Structure match check: API 610 VS4 is defined as a vertical, single‑casing, rigid shaft, suspended pump with discharge head above the pit cover. This is the correct standard type for condensate extraction because:

  • The pump is installed in a pit or directly above the hotwell with the first stage impeller submerged below the minimum operating water level, ensuring flooded suction despite very low NPSHa.

  • Vertical orientation uses minimal floor space and allows direct suction from the condenser neck or hotwell pit.

  • Rigid shaft and line‑shaft bearings can reach down 3‑10 meters to the submerged impeller.

  • The design is optimized for extremely low NPSHr (often < 1.5 m) to prevent cavitation in condensate service.

Why API 610 VS4 for condensate extraction duty?

  • Extremely low NPSH requirement – The first‑stage impeller is specially designed (double‑suction, inducer, or high‑suction specific speed) to operate with NPSHa as low as 1‑2 m, avoiding cavitation and vibration. This is critical for hot condensate near boiling point.

  • Vertical submerged installation – The pump sits on a concrete pit above the hotwell. The suction bell is submerged below the lowest operating water level, providing positive inlet pressure.

  • Continuous, high‑reliability duty – Condensate extraction pumps run 24/7 for months or years. API 610 VS4 with heavy duty bearings, water‑lubricated line shaft bearings, and balanced rotors ensure long MTBR.

  • Corrosion resistance – Condensate is typically pure water, but can become acidic (low pH) due to CO₂ ingress. Wetted parts are specified in 316SS, bronze, or CA6NM (12% chrome). Carbon steel is not acceptable.

  • High flow, moderate head – Typical CEP duty: flow 50‑5000 m³/h, head 100‑300 m, usually achieved with 2‑8 stages (multistage diffuser design inside the single casing).

  • Space saving – The pump sits in a small pit; all maintenance (withdrawal) is vertical, with no need to remove large piping.

Key design features for condensate extraction service

  • Casing – Single casing (not double casing like barrel pumps). Diffuser type stages inside. Discharge head (elbow) above pit cover with flanged nozzle. Materials: cast iron with bronze trim, or 316SS for aggressive condensate.

  • Impeller – First stage: double‑suction or high‑suction specific speed design to minimize NPSHr. Subsequent stages: single‑suction radial impellers. All impellers in bronze, 316SS, or CA6NM.

  • Inducer – Optional on first stage for extremely low NPSH (below 1.5 m). Inducer raises suction pressure, preventing cavitation.

  • Shaft & bearings – Rigid shaft with product‑lubricated rubber bearings (water) at each stage and at intermediate positions (if column length >3 m). Thrust bearing in the motor or in a separate thrust pot (if motor is hollow shaft). For deeper pits, line shaft bearings are grease or product lubricated.

  • Sealing – At the discharge head, a mechanical seal (API 682 Plan 11 or 13) or gland packing is used. For clean condensate, Plan 11 recirculation from discharge is sufficient. For higher pressure, Plan 23 (cooled recirculation) if condensate is hot.

  • Materials – Wetted: bronze (ASTM B584 C90500) or 316SS (CF8M) for impellers and wear rings. Casing: cast iron (ASTM A48) with epoxy coating, or 316SS. Discharge head: carbon steel with stainless trim.

  • NPSH verification – Each pump is tested per API 610 for NPSHr at the specified flow, witnessed if required.

  • Hydrostatic test – Casing and discharge head tested at 1.5× working pressure.

Typical performance range

ParameterValue
Flow rate50 – 5000 m³/h
Head100 – 350 m
TemperatureUp to 90°C (higher for some designs)
Pressure ratingUp to 30 bar (discharge)
NPSHr (first stage)As low as 0.8 – 1.5 m
Speeds1450 / 2900 / 3600 rpm (typically 1450 or 2900)
Stages2 to 8 (depending on head)

Typical applications

  • Fossil power plants – Condensate extraction from main condenser hotwell.

  • Nuclear power plants (conventional island) – Secondary side condensate.

  • Combined cycle / HRSG – Condensate extraction from bottom of HRSG or auxiliary condenser.

  • Industrial steam systems – Condensate return from process condensers.

  • District heating – Condensate extraction from steam-to-water heat exchangers.

Why choose our API 610 VS4 condensate extraction pump?

  • Full API 610 compliance – Type VS4 verified. Performance test, NPSH test, 4‑hour mechanical run test.

  • Optimized low NPSH hydraulics – First‑stage design prevents cavitation, noise, and impeller damage – the main failure mode in condensate extraction.

  • High reliability – Water‑lubricated rubber bearings tolerate occasional dry starts. Balanced rotor and stiff shaft minimize vibration.

  • Corrosion resistant options – Bronze, 316SS, or CA6NM wetted parts for long life in pure or acidic condensate.

  • Easy maintenance – Entire pump can be withdrawn vertically from the pit without disturbing suction or discharge piping.

  • Short lead time – Standard models (cast iron/bronze) available 12‑16 weeks; stainless steel versions 16‑20 weeks.

  • Global spare parts support – Impellers, diffusers, shaft, rubber bearings, mechanical seal, thrust bearing assembly shipped worldwide.

Quality assurance

  • ISO 9001:2015 certified.

  • API 610 mechanical run test (minimum 4 hours) with vibration and bearing temperature monitoring.

  • NPSH test verification (first stage) per API 610.

  • Hydrostatic test of discharge head and casing.

  • Material traceability EN 10204 3.1 / 3.2.

  • Impeller dynamic balancing grade G2.5.

How to specify your condensate extraction pump

Please provide: flow (m³/h), head (m), operating temperature (°C), hotwell submergence (m) or NPSHa available (m), condensate quality (pH, conductivity, presence of oxygen, chlorides), required material (cast iron/bronze, 316SS, or CA6NM), pit depth (if known), and driver type (electric motor with vertical solid shaft or hollow shaft). We will recommend number of stages, first stage type (high suction specific speed or inducer), material grade, and bearing arrangement.

Contact us

For a quotation or technical discussion on condensate extraction pumps (API 610 VS4) :

info@hyrig.com


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit