Rich Liquid Pump – API 610 OH2 / BB3 / VS4 for Rich Amine & Rich Oil Service

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
API 610 rich liquid pump for transferring loaded solvent (rich amine, rich oil) from absorber to regenerator. OH2 single-stage, BB3 multistage for high head, VS4 vertical sump. 316L stainless steel (S-8) wetted parts. API 682 dual pressurized seals Plan 53B for H₂S and volatile hydrocarbon containment. Flows to 1500 m³/h, heads to 1500 m. 20-year design life, 3-year continuous run.

Conatct For Details
DetailReview(0)Additional

Product Overview

The Rich Liquid Pump is specifically designed to transfer “rich” solvent – liquid that has absorbed acid gases or hydrocarbons – from the bottom of an absorber or contactor to the regenerator or stripping vessel. The most common rich liquids are:

  • Rich amine (MDEA, MEA, DEA loaded with H₂S and CO₂) in natural gas sweetening, refinery HDS, and CCUS.

  • Rich oil (lean oil that has absorbed heavier hydrocarbons) in natural gas liquids (NGL) recovery or refinery off‑gas treatment.

Rich liquids are typically corrosive (due to H₂S, CO₂, and heat‑stable salts), may be at elevated temperatures, and contain hazardous or flammable components. Therefore, these pumps must meet the highest standards of reliability, corrosion resistance, and leakage containment. All pumps in this series are fully compliant with API 610 11th/12th edition (ISO 13709) – ensuring a 20‑year design life and minimum 3‑year uninterrupted operation.

Key Characteristics of Rich Liquid Service

ParameterRich AmineRich Oil
Typical fluidMDEA/MEA/DEA + H₂S + CO₂ + waterHydrocarbons (C2–C6+) + lean oil
H₂S contentPresent (toxic, corrosive)May be present (sour service)
CorrosivityHighModerate to high (if sour)
Temperature40 – 80°C (absorber bottom)10 – 50°C (typical)
Vapour pressureLow (but dissolved gases present)Moderate to high (volatile components)

Pump Configurations for Rich Liquid Transfer

Pump TypeConfigurationBest Rich Liquid Application
OH2 (Preferred)Overhung, centreline‑mounted, single‑stageStandard rich amine transfer (heads ≤150 m); rich oil transfer; flows up to 600 m³/h
BB3Axially split, multistage, between bearingsHigh‑head rich liquid (>150 m) where absorber is at high pressure or regenerator is elevated
VS4Vertical suspended sump / can typeSump collection of rich liquid from drains or low‑point pits; low NPSHa installations

Key Technical Specifications

ParameterOH2BB3VS4
Flow range10 – 600 m³/h50 – 1500 m³/h10 – 750 m³/h
Head range20 – 260 m (transfer usually ≤150 m)100 – 1500 m15 – 280 m
Pressure ratingUp to 64 barUp to 150 barUp to 40 bar
Temperature–45 to +200°C–45 to +200°C–46 to +260°C
Speed1,450 / 2,950 rpm1,450 / 2,950 rpm1,450 / 2,950 rpm

Materials – API 610 Table H

Rich amine (containing H₂S and CO₂) is corrosive. Rich oil may be non‑corrosive unless H₂S is present. For sour rich oil, NACE MR0175 applies.

ComponentRich Amine (Standard)Rich Oil (Clean)Rich Oil (Sour)
Casing316L SS (S‑8)Carbon steel (C‑6)316L SS or Duplex (D‑1)
Impeller316L SSCarbon steel316L SS or Duplex
Shaft316 SS or 4140 coated41404140 or 316 SS
Wear rings316L SS + StelliteHardened 4140Hardened + coating
GasketsSpiral wound (graphite)Spiral woundSpiral wound (NACE)

316L stainless steel (S‑8) is strongly recommended for rich amine service – carbon steel will corrode rapidly. For rich oil without H₂S, carbon steel is acceptable. For sour rich oil (H₂S present), select 316L SS or duplex with NACE MR0175 certification.

Mechanical Seals – API 682 Compliance

Rich liquid often contains H₂S (toxic) or volatile hydrocarbons (flammable). Fugitive emissions must be prevented. Dual pressurised seals (API 682 Arrangement 3) with Plan 53B are the industry standard for rich amine and sour rich oil.

ServiceRecommended SealAPI 682 PlanNotes
Rich amine (H₂S)Dual pressurised (Arr. 3)Plan 53B (bladder accumulator)Zero emissions, mandatory for H₂S
Rich oil (sour)Dual pressurised (Arr. 3)Plan 53BH₂S containment
Rich oil (non‑sour, low pressure)Single seal (Arr. 1)Plan 11 / 21Acceptable; Plan 62 quench optional

Plan 53B provides barrier fluid pressurised above process pressure, eliminating leakage. The bladder accumulator prevents nitrogen entrainment. Seal faces: silicon carbide (SiC) / SiC. Elastomers: FKM (Viton) for moderate temperatures; Aflas for high‑temperature or aggressive chemicals.

NPSH Considerations

Rich liquid pumps typically take suction from the bottom of an absorber operating at moderate to high pressure (5–20 barg). Therefore, NPSHa is usually high and not a limiting factor. However, dissolved gases can flash across control valves, so ensure that between the pump and the suction source there is no pressure drop that would cause gas breakout. For rich oil from low‑pressure scrubbers, NPSHa may be limited – then a VS4 vertical pump or inducer should be considered.

Minimum Flow Protection

Because rich liquid flow is directly tied to gas throughput, the pump may experience turndown. An automatic recirculation valve (ARC) or bypass line with orifice must be provided to maintain minimum flow when the main discharge valve closes. This is especially critical for BB3 multistage pumps.

Applications for Rich Liquid Pump

IndustryRich LiquidPump Configuration
Natural gas sweeteningRich MDEA / MEAOH2 (standard) or BB3 (high head)
Refinery HDSRich MDEA / DEAOH2
Claus tail gas treatmentRich MDEAOH2
CCUS (carbon capture)Rich MEAOH2 (larger flows)
NGL recoveryRich oil (C2+ hydrocarbons)OH2 or BB3
Refinery off‑gas treatmentRich oil (absorber bottoms)OH2

API 610 Compliance Highlights

  • Design life: 20 years minimum

  • Continuous operation: Minimum 3 years uninterrupted service

  • Bearing life: L10 ≥25,000 hours

  • Critical speed: ≥120% of maximum operating speed

  • Centreline mounting (OH2/BB3): Thermal stability

  • Hydrostatic test: 1.5x design pressure

  • Performance test: Water per API 610 Grade 1 or 2

  • Material certification: EN 10204 3.1 full traceability

  • NACE MR0175 / ISO 15156 certification available for sour service

Why Choose Our Rich Liquid Pump?

  • Full API 610 compliance (OH2 / BB3 / VS4) – 11th/12th edition ISO 13709, 20‑year life

  • 316L stainless steel (S‑8) as standard for rich amine – proven corrosion resistance

  • API 682 Plan 53B dual pressurised seals – zero emissions, H₂S containment

  • Broad hydraulic coverage – flows 10–1500 m³/h, heads 20–1500 m

  • Low NPSH designs – inducer option for rich oil low‑suction applications

  • Centreline mounting – handles up to 200°C

  • Easy maintenance – back pull‑out (OH2), axial split (BB3)

  • Minimum flow protection integrated

  • NACE MR0175 compliant options – for sour rich oil or rich amine with high H₂S

  • Field proven – thousands operating in gas plants and refineries worldwide

Recommended Spare Parts (Per Pump)

ComponentRecommended Quantity
Mechanical seal cartridge (Plan 53B ready)1 set
Bearing set (radial + thrust)1 set
Wear ring set1 set
Gasket / O‑ring kit1 set

Get a Quote or Engineering Support

For selection of the correct Rich Liquid Pump for your application – including fluid composition (rich amine or rich oil), H₂S partial pressure, flow and head requirements, material selection (316L SS, duplex, or NACE MR0175), API 682 seal plan (Plan 53B for H₂S service), and complete API 610 data sheet – please contact our engineering team.

Email: info@hyrig.com

Our engineers support gas sweetening, refinery HDS, NGL recovery, and carbon capture projects worldwide with reliable, emissions‑compliant API 610 rich liquid pumps – from rich amine to rich oil.


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit