The Amine Circulation Pump is the heart of any amine sweetening unit. It continuously circulates alkanolamine solutions (MDEA, MEA, DEA) between the absorber and the regenerator, enabling the removal of H₂S and CO₂ from natural gas, refinery fuel gas, or syngas. Lean amine (regenerated, low acid‑gas content) is pumped from the stripper to the high‑pressure absorber, while rich amine (loaded with acid gases) is returned to the regenerator. Depending on system pressure and flow requirements, the pump can be configured as an OH2 single‑stage, BB3 multistage, or VS4 vertical sump pump, all fully compliant with API 610 11th/12th edition (ISO 13709) – guaranteeing a 20‑year design life and minimum 3‑year uninterrupted operation.
| Pump Type | Configuration | Amine Circulation Duty |
|---|---|---|
| OH2 | Overhung, centreline‑mounted, single‑stage | Lean amine circulation from regenerator to absorber (heads ≤260 m); rich amine transfer; reflux; booster duties |
| BB3 | Axially split, multistage, between bearings | High‑head lean amine charge (heads >260 m) for high‑pressure absorbers; high‑pressure rich amine systems |
| VS4 | Vertical suspended sump / can type | Amine sump evacuation, pit drainage, low‑NPSHa transfer from storage |
| Parameter | OH2 | BB3 | VS4 |
|---|---|---|---|
| Flow range | 10 – 600 m³/h | 50 – 1500 m³/h | 10 – 750 m³/h |
| Head range | 20 – 260 m | 100 – 1500 m | 15 – 280 m |
| Pressure rating | Up to 64 bar | Up to 150 bar | Up to 40 bar |
| Temperature | –45 to +200°C | –45 to +200°C | –46 to +260°C |
| Speed | 1,450 / 2,950 rpm | 1,450 / 2,950 rpm | 1,450 / 2,950 rpm |
Amine solutions (especially rich amine) are corrosive due to dissolved H₂S, CO₂, heat‑stable salts, and possibly chlorides. Therefore, 316L stainless steel (API 610 Class S‑8) is the standard material for all wetted parts. Carbon steel (C‑6) is not recommended.
| Component | Material (Standard) | Upgrade Option |
|---|---|---|
| Casing | 316L SS (CF3M) | Duplex (D‑1/D‑2), Super Duplex (U‑8) |
| Impeller | 316L SS | Duplex, Super Duplex, 17‑4 PH |
| Shaft | 316 SS or 4140 with coating | 17‑4 PH, Duplex |
| Wear rings | 316L SS + Stellite hard‑facing | Tungsten carbide |
| Gaskets / O‑rings | Spiral wound (graphite) / FKM | Aflas for high temperature |
For sour amine service (rich amine with H₂S partial pressure above NACE limits), materials must be certified to NACE MR0175 / ISO 15156.
Rich amine contains toxic H₂S; lean amine may also release H₂S. Fugitive emissions must be prevented. The industry standard is a dual pressurised seal (API 682 Arrangement 3) with Plan 53B (bladder accumulator) .
| Seal Arrangement | API 682 Plan | Application |
|---|---|---|
| Dual pressurised (Arr. 3) | Plan 53B | Recommended for all rich and lean amine circulation (zero emissions) |
| Tandem seal (Arr. 2) | Plan 52 | Acceptable for lean amine only (lower H₂S risk) |
| Single seal (Arr. 1) | Plan 11 / 21 | Not permitted for H₂S service |
Plan 53B provides barrier fluid pressurised above process pressure, eliminating amine leakage. The bladder accumulator prevents nitrogen entrainment into the amine. Seal faces: silicon carbide (SiC) / SiC. Elastomers: FKM for up to 120°C; Aflas for higher temperatures.
Amine circulation pumps often face limited NPSHa (atmospheric storage tanks, reflux drums, or sumps). Because amines contain dissolved gases (H₂S, CO₂, methane), the fluid is at or near its bubble point. Do not assume subcooling when calculating NPSHa. Ensure NPSHa ≥ NPSHr + 1.0 m per API 610. An inducer can be added to the first‑stage impeller for very low NPSHa conditions.
All amine circulation pumps must be protected from operation below Minimum Continuous Stable Flow (MCSF). An automatic recirculation valve (ARC) or a continuous bypass line with orifice returns minimum flow to the suction vessel (tank or drum). This is especially critical for BB3 high‑head multistage pumps.
| Process | Amine Type | Pump Configuration |
|---|---|---|
| Natural gas sweetening | MDEA / MEA | OH2 for lean circulation; OH2 for rich transfer |
| Refinery HDS (hydrodesulfurization) | MDEA / DEA | BB3 for high‑pressure lean charge; OH2 for circulation |
| Claus tail gas treatment | MDEA / DIPA | OH2 circulation pumps |
| CCUS (carbon capture) | MEA | OH2 circulation pumps (larger flows) |
| Amine storage / handling | MDEA / MEA | OH2 transfer; VS4 sump pumps |
Design life: 20 years minimum
Continuous operation: Minimum 3 years uninterrupted service
Bearing life: L10 ≥25,000 hours (API 610 mandatory)
Critical speed: ≥120% of maximum operating speed
Centreline mounting (OH2/BB3): Maintains alignment for hot amine (up to 200°C)
Hydrostatic test: 1.5x design pressure
Performance test: Water per API 610 Grade 1 or 2
Material certification: EN 10204 3.1 (full traceability)
NACE MR0175 / ISO 15156 available for sour service
Full API 610 compliance – OH2, BB3, VS4 types; 11th/12th edition ISO 13709
316L stainless steel (S‑8) as standard – proven 20‑year corrosion resistance in amine service
API 682 Plan 53B dual pressurised seals – zero emissions, H₂S containment
Broad hydraulic coverage – flows 10–1500 m³/h, heads 20–1500 m
Low NPSH designs – inducer option for challenging suction conditions
Centreline mounting – thermal stability for hot amine (up to 200°C)
Easy maintenance – back pull‑out (OH2), axial split (BB3), vertical withdrawable (VS4)
Minimum flow protection – ARC or bypass integrated
NACE MR0175 compliant options – for sour rich amine
Field proven – thousands installed in gas plants, refineries, and CCUS facilities
| Component | Recommended Quantity |
|---|---|
| Mechanical seal cartridge (Plan 53B ready) | 1 set |
| Bearing set (radial + thrust) | 1 set |
| Wear ring set | 1 set |
| Gasket / O‑ring kit | 1 set |
| Inducer (if fitted) | 1 set |
For selection of the right Amine Circulation Pump – including hydraulic sizing, material selection (316L SS, duplex, or NACE MR0175), API 682 seal plan (Plan 53B), NPSHa verification, and complete API 610 data sheet – please contact our engineering team.
Email: info@hyrig.com
Our engineers support gas sweetening, refinery HDS, carbon capture, and amine regeneration projects worldwide with reliable, emissions‑compliant API 610 amine circulation pumps – from lean amine to rich amine, OH2 to BB3 to VS4.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.