The Amine Transfer Pump is purpose-built for transporting lean amine (regenerated, low acid gas content) and rich amine (loaded with H₂S and CO₂) across gas sweetening units, refinery hydrodesulfurization (HDS) plants, Claus tail gas treatment units, and carbon capture (CCUS) facilities. These pumps handle corrosive, toxic, and sometimes high-temperature amine solutions including MDEA, MEA, and DEA.
All pumps are fully compliant with API 610 11th/12th edition (ISO 13709) standards, guaranteeing a minimum 3‑year uninterrupted operation and a 20‑year design life. The series covers all typical amine transfer duties – from inter-tank transfer and sump evacuation to high‑pressure lean amine circulation.
Depending on flow, head, and installation requirements, three API 610 configurations are available.
| Pump Type | Configuration | Best Amine Transfer Application |
|---|---|---|
| OH2 | Overhung, centreline-mounted, single-stage | Lean amine transfer between regenerator and absorber; rich amine transfer; tank-to-process transfer; flow up to 1,000 m³/h, head up to 260 m |
| BB3 | Axially split, single casing, multistage, between bearings | High‑head lean amine charge (exceeding 260 m) where high pressure is required; also for rich amine service in tall columns |
| VS4 | Vertical suspended sump/can type | Sump evacuation; tank transfer with low NPSHa; fire-code compliant vertical installation in amine storage areas |
The OH2 configuration is the most frequently specified for amine transfer duties. Characteristics include:
Single-stage overhung impeller, centreline mounted for thermal stability
Back pull-out design – rotating assembly removable without disturbing piping
API 610 bearing housing with oil bath lubrication; L10 bearing life ≥25,000 hours
Flow up to 1,000 m³/h (higher with larger frames)
Head up to 260 m
Temperature –45°C to +200°C
Standard wetted material: 316L stainless steel (API 610 Class S‑8)
Ideal for lean amine circulation, rich amine transfer from absorber to regenerator, MDEA solution handling, and general process transfer.
For applications requiring head above 260 m (e.g., tall regenerator feed into high-pressure absorbers), the BB3 multistage pump provides:
Horizontally split single casing, between bearings
Opposed (back-to-back) impellers for axial thrust self‑balancing – no balance disc or drum
Dual volute or diffuser stages balancing radial thrust
Flow up to 1,500 m³/h, head up to 1,500 m, pressure up to 150 bar
Same material flexibility as OH2 (S‑8 standard, duplex optional)
When amine needs to be pumped from below‑grade sumps, spill collection pits, or low NPSHa tanks, the VS4 vertical suspended pump offers:
Vertically suspended, single or multistage, diffuser-type pump
Wet pit installation – suction strainer optional
Flow up to 750 m³/h, head up to 280 m, pressure up to 40 bar
Temperature –46°C to +260°C
Ideal for amine tank farm sumps, collection basins, and emergency transfer
| Parameter | OH2 | BB3 | VS4 |
|---|---|---|---|
| Flow range | Up to 1,000 m³/h | Up to 1,500 m³/h | Up to 750 m³/h |
| Head range | Up to 260 m | Up to 1,500 m | Up to 280 m |
| Pressure rating | Up to 64 bar | Up to 150 bar | Up to 40 bar |
| Temperature | –45 to +200°C | –45 to +200°C | –46 to +260°C |
| Speed | 1,450 / 2,950 rpm | 1,450 / 2,950 rpm | 1,450 / 2,950 rpm |
| Stages | 1 | 3 – 14 | 1 – 8 |
Amines (especially rich amine containing H₂S and CO₂) are corrosive. Proper material selection is critical.
| Component | Recommended Material (API 610 Class) | Remarks |
|---|---|---|
| Casing | 316L stainless steel (S‑8) | CF3M casting; resists pitting and general corrosion |
| Impeller | 316L stainless steel (S‑8) | Same as casing |
| Shaft | 316 SS or 4140 with coating | Corrosion-resistant or hardened |
| Wear rings | 316L SS + Stellite hard-facing | Extended life |
| Gaskets | Spiral wound (graphite filled) | For flanges and casing joints |
| Fasteners | 316 SS | Prevents galvanic corrosion |
Carbon steel (C‑6) is not recommended for amine transfer because water, H₂S, and CO₂ cause rapid general corrosion and pitting. 316L SS (S‑8) is the industry standard and has proven successful for decades.
For amine streams with chlorides (e.g., from cooling water contamination) or very high H₂S partial pressures, duplex (D‑1/D‑2) or super duplex can be specified. NACE MR0175 / ISO 15156 compliance is available for sour amine service.
Rich amine contains H₂S – a toxic, hazardous gas. Lean amine is less hazardous but still requires containment. Dual pressurised seals are strongly recommended for all amine transfer pumps.
| Service | Recommended Seal | API 682 Plan | Notes |
|---|---|---|---|
| Lean amine (low H₂S) | Tandem seal (Arr. 2) | Plan 52 | Buffer fluid collects any leakage |
| Lean amine (premium) / Rich amine | Dual pressurised (Arr. 3) | Plan 53B (bladder accumulator) | Zero emissions; barrier fluid pressure > process |
| Lean amine booster (clean, low pressure) | Single seal (Arr. 1) | Plan 11 / 21 | Acceptable only where H₂S is negligible |
Plan 53B with bladder accumulator is the preferred arrangement for all H₂S‑containing amine transfer. It provides:
Barrier fluid pressurised above process pressure (no process leakage)
No nitrogen entrainment into process (unlike Plan 53A)
Visual level indicator and low‑pressure alarm
Compliance with strict refinery HSE requirements
Seal faces: Silicon carbide (SiC) / SiC or tungsten carbide for abrasive service. Elastomers: FKM (Viton) or Aflas for high‑temperature amine.
Amine transfer pumps often take suction from:
Atmospheric storage tanks (NPSHa 2–5 m)
Reflux drums (low NPSHa)
Sump pits (NPSHa may be near zero)
To ensure reliable operation:
Select pumps with low NPSHr (optimised first‑stage impeller, large eye)
Consider inducer option for very low NPSHa
Maintain NPSHa ≥ NPSHr + 1.0 m per API 610
Do not assume subcooling – calculate NPSHa at bubble point because amine contains dissolved gases (H₂S, CO₂, methane)
During start‑up, shutdown, or low‑demand periods, amine transfer pumps must be protected from low‑flow operation. A minimum flow recirculation line (with orifice or automated recirculation valve) returns flow to the suction source (tank or drum). This prevents overheating, cavitation, and mechanical seal damage.
| Application | Fluid | Typical Duty | Recommended Configuration |
|---|---|---|---|
| Lean amine from regenerator to absorber | Lean MDEA/MEA | Q 50–500 m³/h, H 50–250 m | OH2 |
| Rich amine from absorber to regenerator | Rich MDEA/MEA (H₂S) | Q 50–500 m³/h, H 50–150 m | OH2 |
| High‑pressure lean amine charge | Lean amine | Q 100–1000 m³/h, H >260 m | BB3 |
| Amine transfer from tank farm to process | MDEA/MEA | Q 30–300 m³/h, H 30–80 m | OH2 |
| Amine sump evacuation | Lean/rich amine | Q 10–100 m³/h, H 20–60 m | VS4 |
| Amine make‑up / dump transfer | Fresh amine | Q 10–50 m³/h, H 20–60 m | OH2 or VS4 (vertical) |
| CCUS amine circulation | Lean MEA | Q 100–600 m³/h, H 60–200 m | OH2 |
Design life: 20 years minimum
Continuous operation: Minimum 3 years uninterrupted service
Bearing life: L10 ≥25,000 hours (API 610 mandatory)
Critical speed: First lateral critical speed ≥120% of maximum operating speed
Centerline mounting (OH2/BB3): Maintains alignment during thermal cycling
Hydrostatic testing: Casing tested at 1.5x design pressure
Performance testing: Water performance test per API 610 Grade 1 or 2
Material certification: EN 10204 3.1 (full traceability for pressure‑containing parts)
NACE MR0175 / ISO 15156 optional for sour amine service
Full API 610 compliance (OH2/BB3/VS4) – 11th/12th edition ISO 13709, 20‑year life, 3‑year continuous run
316L stainless steel (S‑8) as standard – field‑proven corrosion resistance for all amine services
API 682 Plan 53B dual pressurised seals – zero emissions, mandatory for H₂S‑containing rich amine
Broad hydraulic coverage – flows 10–1,500 m³/h, heads 20–1,500 m
Low NPSH designs – inducer option for challenging suction conditions
Centerline mounting – thermal stability for hot amine (up to 200°C)
Back pull‑out (OH2) / axial split (BB3) / vertical withdrawable (VS4) – reduced maintenance downtime
Minimum flow provisions – protect pump during turndown
NACE MR0175 / ISO 15156 compliant materials available – for sour amine with H₂S
Proven field experience – thousands of API 610 amine transfer pumps in gas plants and refineries worldwide
| Component | Recommended Quantity |
|---|---|
| Mechanical seal cartridge (API 682 Plan 53B ready) | 1 set per pump |
| Bearing set (radial + thrust) | 1 set |
| Wear ring set (casing + impeller) | 1 set |
| Gasket / O-ring kit | 1 set per pump |
| Inducer (if fitted) | 1 set |
For detailed selection of the correct Amine Transfer Pump for your gas sweetening or refinery application – including flow and head calculations, NPSHa verification, material selection (316L SS S‑8 or duplex D‑1/D‑2 for chlorides), API 682 seal plan (Plan 53B for rich amine H₂S service), and complete API 610 data sheet – please contact our engineering team.
Email: info@hyrig.com
Our engineers support natural gas sweetening, refinery HDS, carbon capture, and amine regeneration projects worldwide with reliable API 610 amine transfer pumps – from lean amine circulation to rich amine transfer.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.