Slop Oil Pump | API 610 OH2 Centrifugal Pump | China OH2 Pump Manufacturer

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
API 610 OH2 single‑stage, overhung pump for slop oil / oily waste service. Handles hydrocarbons, water emulsions, and small solids. Designed for low NPSH and intermittent operation. Corrosion resistant materials available. China OH2 pump manufacturer.

Conatct For Details
DetailReview(0)Additional

A slop oil pump (also called oily waste pump, sump pump, or contaminated hydrocarbon pump) handles a mixture of hydrocarbons, water, emulsions, and often small amounts of solids. Slop oil originates from refinery drains, tank bottoms, equipment washdowns, and other waste streams. This fluid is typically corrosive, has variable viscosity, low net positive suction head (NPSH), and may contain abrasive particles. Our API 610 OH2 centrifugal pump is specifically engineered for reliable slop oil service. This design fully complies with API 610 11th/12th edition (ISO 13709) .

Structure match check: API 610 OH2 is defined as a horizontal, single‑stage, overhung pump with foot‑mounted casing, back pull‑out design, and centerline support for higher temperature service (or foot‑mounted for ambient). This matches the requirements for slop oil duty: easy maintenance (frequent cleaning/seal replacement), ability to handle dirty fluids, and options for corrosion/abrasion resistance. Back pull‑out allows rotor, seal, and bearing removal without disturbing piping – critical when slop contains abrasive solids that wear seals.

Why API 610 OH2 for slop oil duty?

  • Easy maintenance – Slop oil often contains debris and emulsions that can foul seals. Back pull‑out design allows quick access to the seal, impeller, and wear rings without removing the casing from piping.

  • Solids handling capability – Open or semi‑open impeller options (up to 10 mm particle passage) prevent clogging. Replaceable wear rings and front liners protect casing from abrasion.

  • Corrosion resistance – Wetted materials available in 304SS, 316SS, duplex, or Alloy 20 for saline or acidic slop. Standard carbon steel also available for less corrosive service.

  • Low NPSH capability – Optional inducer reduces NPSHr to below 1 m, preventing cavitation when pumping from slop tanks with low liquid levels.

  • API 682 seal compatibility – Single mechanical seal with Plan 11 (recirculation) is common. For aggressive slop with solids, Plan 31 (cyclone separator) or Plan 32 (external clean fluid flush) is recommended to protect seal faces. Tandem/double seals with barrier fluid for zero emissions if required.

  • Intermittent duty robust – Slop pumps often run intermittently. OH2 design with heavy duty bearings and API 682 seals withstands frequent start/stop cycles.

  • Wide viscosity range – Handles fluids from light hydrocarbons to heavy oil/water emulsions up to 1000 cSt (with efficiency derate).

  • Flow range – 5 to 1500 m³/h, head up to 150 m.

Key design features for slop oil service

  • Impeller types – Closed impeller for clean slop; semi‑open or open impeller (with replaceable wear plate) for slop containing solids up to 6‑10 mm.

  • Materials – Casing: carbon steel, 316SS, or duplex. Impeller/shaft: 12% chrome, 316SS, duplex, or Alloy 20. Wear rings: hardened stainless or Stellite.

  • Seal flush plans – Plan 11 (internal recirculation) for clean slop; Plan 31 (cyclone separator) for solids up to 100 microns; Plan 32 (external clean fluid) for very abrasive slop.

  • Bearing housing – Oil lubricated with labyrinth seals. For steam cleaning or hot slop, cooling fan or water jacket optional.

  • Drain connections – Full bottom drain for complete removal of settled solids during maintenance.

  • Vent connections – For vapor release from volatile slop streams (gasoline, naphtha contaminated).

Typical performance range

ParameterValue
Flow rate5 – 1500 m³/h
HeadUp to 150 m
Temperature-20°C to +150°C
Pressure ratingUp to 25 bar
NPSHr (with inducer)As low as 0.5 m
Viscosity range1 – 1000 cSt
Solids passage (open impeller)Up to 10 mm

Typical applications

  • Refinery slop oil recovery – Pumping from slop tanks to charge into crude unit, coker, or other processors.

  • Terminal stormwater / oily sump – Collecting and transferring oily water to oil/water separators.

  • Tank bottom drainage – Pumping mixed hydrocarbon/water/solids from storage tank cleaning.

  • Washdown sumps – From equipment cleaning areas in refineries, petrochemical plants.

  • Produced water / oily waste – Onshore or offshore facilities (with corrosion resistant materials).

  • Marine slop disposal – From shipboard oily waste systems.

Why choose our API 610 OH2 slop oil pump?

  • Full API 610 compliance – Verified per standard. Mechanical run test, vibration & temperature monitoring included.

  • Abrasion and corrosion resistant – Options for hard facing, stainless steels, and seal protection plans.

  • Low NPSH – Inducer option enables reliable pumping from low‑level slop tanks.

  • Easy solids removal – Open impeller, wear plate, and casing bottom drain simplify cleaning.

  • Short lead time – Standard sizes ex‑stock; custom material combinations 6‑8 weeks.

  • Global spare parts support – Impellers, seals, wear rings, shafts, bearings shipped worldwide.

  • Lower total cost – Competitive price + reduced downtime for seal/impeller replacement.

Quality assurance

  • ISO 9001:2015 certified.

  • API 610 mechanical run test (minimum 4 hours) with vibration and bearing temperature monitoring.

  • Hydrostatic test of casing.

  • Material traceability EN 10204 3.1 / 3.2.

  • NDE – MT, PT, UT as required.

  • Impeller balancing per grade G2.5.

How to specify your slop oil pump

Please provide: flow (m³/h), head (m), operating temperature (°C), NPSHa (m), fluid composition (oil%, water%, solids content and size, pH, chlorides, H₂S). Also indicate if the slop contains abrasive particles (sand, catalyst fines) or requires zero fugitive emissions. We will recommend impeller type (open/semi‑open/closed), material class, seal plan, inducer (yes/no), and driver details.

Contact us

For a quotation or technical discussion on slop oil pumps (API 610 OH2) :

info@hyrig.com


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit