Heavy Oil Pump | API 610 BB2 & OH2 | China Heavy Oil Pump Manufacturer

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
API 610 BB2 (axially split multistage, between-bearings) and OH2 (single-stage, overhung) pumps for heavy oil service. Designed for high viscosity, high temperature (up to 400°C). Suitable for heavy crude, fuel oil, bitumen, and resid. China heavy oil pump manufacturer.

Conatct For Details
DetailReview(0)Additional

A heavy oil pump must handle fluids with high viscosity (often 100-2000 cSt or higher), high temperature (up to 400°C), and possibly containing some solids (e.g., asphaltenes, catalyst fines). Our API 610 BB2 and OH2 pumps are specifically engineered for reliable heavy oil transfer in refineries, heavy crude pipelines, and fuel oil systems. Both designs fully comply with API 610 11th/12th edition (ISO 13709) , with different structural types as defined by the standard.


API 610 OH2 – Single‑Stage Heavy Oil Pump

Structure match check: API 610 OH2 is defined as a horizontal, single‑stage, overhung pump with foot‑mounted casing and centerline support for high temperature. This is suitable for lower‑head heavy oil duties where head requirements are below approximately 150 m. Common applications include fuel oil forwarding, tank farm transfer, and low‑head pipeline boost.

Why OH2 for heavy oil?

  • Compact, economical for low to medium head (up to 150 m).

  • Centerline support – handles thermal expansion up to 400°C without misalignment.

  • Back pull‑out design – allows seal, bearing, and rotor inspection without removing casing from piping. Important for heavy oil where seal and wear ring life may be shorter due to abrasives.

  • Viscosity handling – Hydraulic performance corrected for high viscosity. Impeller trimming or speed reduction (VSD) maintains efficiency.

  • API 682 seal compatibility – Single or tandem mechanical seals with heat tracing, quench, or external flush to prevent coking. Plan 23 (cooled recirculation) or Plan 32 (external clean oil flush) recommended.

  • Flow range – 5 to 2000 m³/h.

  • Head range – up to 150 m.

  • Optional steam jacket – For heavy oil that solidifies at ambient temperature, casing and seal housings can be steam traced or jacketed.

Typical OH2 applications

  • Fuel oil forwarding pumps (refinery to heaters, boilers)

  • Heavy crude tank farm transfer (low head)

  • Viscous oil pipeline booster

  • Asphalt / bitumen loading (with heating)


API 610 BB2 – Multistage Heavy Oil Pump

Structure match check: API 610 BB2 is defined as a horizontal, axially split, multistage, between‑bearings pump. This design is required when heavy oil pumps need higher heads (150-800 m) – for example, feeding a delayed coker, sending resid to deep storage, or long‑distance heavy crude pipelines.

Why BB2 for heavy oil?

  • Multistage (2 to 10+ stages) – achieves higher heads (up to 800 m) than OH2, essential for heavy oil with high pipeline friction losses.

  • Axially split casing – allows full internal inspection, cleaning of viscous deposits, and replacement of stage parts without disturbing piping.

  • Between‑bearings rotor – superior shaft rigidity reduces deflection, critical for viscous fluids that generate high radial loads.

  • High temperature capability – centerline support or foot‑mounted with expansion joints.

  • Viscosity handling – Same hydraulic correction as OH2, but multistage design allows higher pressure without overspeeding.

  • Steaming / heating options – Casing can be jacketed or steam traced for heavy oil that requires heating to reduce viscosity.

  • Flow range – 20 to 2000 m³/h.

  • Head range – up to 800 m.

Typical BB2 applications

  • Heavy crude pipeline mainline pumps (long distance)

  • Vacuum resid charge to delayed coker or visbreaker

  • Asphalt / bitumen transfer (heated)

  • Refinery heavy oil feed to downstream units requiring high pressure


Comparison & Selection Guide

FeatureOH2 (Single‑stage)BB2 (Multistage)
API 610 typeOH2 – horizontal overhung, foot-mounted, centerline supportBB2 – horizontal axially split, between-bearings, multistage
Head rangeUp to 150 m (typical)Up to 800 m
Flow range5 – 2000 m³/h20 – 2000 m³/h
Casing accessBack pull‑out (rotor only)Axially split – full internal access
Rotor supportOverhung (bearings on one end)Between‑bearings (both ends)
Viscosity limitUp to 2000 cSt (with correct impeller size)Up to 2000 cSt (performance corrected)
Best forLow head, moderate flow, easy maintenanceHigh head, large flow, long-distance transfer
MaintenanceQuick seal/impeller change without pipingLonger downtime for full split, but easier cleaning of heavy deposits

Key design features for both OH2 & BB2 (heavy oil service)

  • High temperature construction – Centerline support or expansion joints. Casing, bearing housing, and seal housing can be water-cooled or thermally insulated.

  • Viscosity correction – Standard pump selection must correct head, flow, efficiency, and NPSH for viscosity using HI methods (e.g., correllation factor K). Impeller size may be increased or speed reduced to maintain performance.

  • Heating provision – Steam jackets or electric heat tracing on casing, seal chambers, and suction/discharge nozzles to keep heavy oil fluid during start‑up or shutdown. Plan 62 quench on seal gland prevents coke buildup.

  • Abrasion resistance – For heavy oils with catalyst fines or coke particles, impellers and wear rings in hardened 12% chrome (CA6NM) or with Stellite overlay.

  • Materials – Carbon steel casing (WCB, LCC, WC6 for high temp). Impeller/shaft in 12% chrome or 316SS. NACE MR0175 optional if H₂S present in heavy oil (e.g., sour resid).

  • Sealing – API 682 Plan 23 (cooled recirculation) for hot heavy oil; Plan 32 (external clean oil flush) for dirty or coking service; double seals with barrier fluid for emission control.

  • Bearing lubrication – Pure oil mist recommended for high temperature service. Cooling water jacket on bearing housing for operation above 200°C ambient.

Why choose our API 610 heavy oil pumps?

  • Full API 610 compliance – OH2 and BB2 types verified per standard. Performance test (viscosity corrected), mechanical run test.

  • Heavy duty heating / cooling options – Steam jacketing, quench glands, bearing cooling – tailored to your fluid.

  • High viscosity expertise – Correct hydraulic sizing prevents under‑performance and energy waste.

  • Abrasion protection – Hardened trim available for heavy oils with particulate.

  • Short lead time – Standard pump sizes with heating features ex‑stock; custom hydraulics 8‑12 weeks.

  • Global spare parts support – Impellers, shafts, casings (OH2), stage pieces (BB2), bearings, seals shipped worldwide.

Quality assurance

  • ISO 9001:2015 certified.

  • API 610 mechanical run test (minimum 4 hours) with vibration and bearing temperature monitoring.

  • Hydrostatic test of casing.

  • Material traceability EN 10204 3.1 / 3.2.

  • NDE – MT, PT, UT as required.

  • Impeller dynamic balancing grade G2.5.

How to specify your heavy oil pump

Please provide: flow (m³/h), head (m), operating temperature (°C), viscosity (cSt at pumping temperature), specific gravity, NPSHa (m), solids content and size (if any), fluid composition (e.g., heavy crude, fuel oil #6, bitumen, resid), H₂S content (for NACE), and whether heating (steam/electrical) will be used. Also indicate required head: low (OH2) or high (BB2). We will recommend pump type, stage count (if BB2), impeller design, sealing plan, heating options, material class, and driver details.

Contact us

For a quotation or technical discussion on heavy oil pumps (API 610 BB2 or OH2) :

info@hyrig.com


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit