Tower Bottom Pump | API 610 OH2 & BB2 | China Tower Bottom Pump Manufacturer

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
API 610 OH2 (horizontal single-stage) and BB2 (axially split multistage) pumps for tower bottom service. High temperature handling (up to 400°C), viscous fluids, particulates. Suitable for crude, vacuum, FCC, and coker fractionator bottoms. China OH2/BB2 pump manufacturer.

Conatct For Details
DetailReview(0)Additional

A tower bottom pump (also called a bottoms pump or sump pump) handles the heavy liquid leaving the bottom of a distillation column, stripper, or fractionator. This fluid is typically at high temperature (often 300-400°C), may be viscous (e.g., reduced crude, vacuum resid, tar), and can contain small amounts of solids (catalyst fines, coke). Our API 610 OH2 and BB2 pumps are specifically engineered for this severe duty. Both designs fully comply with API 610 11th/12th edition (ISO 13709) , with different structural types as defined by the standard.


API 610 OH2 – Single‑Stage Tower Bottom Pump

Structure match check: API 610 OH2 is defined as a horizontal, single‑stage, overhung pump with foot‑mounted casing and centerline support for high temperature. This is suitable for lower‑head tower bottom duties where head requirements are below approximately 150-200 m. Common in atmospheric crude columns, vacuum flashers, and some product strippers.

Why OH2 for tower bottom?

  • Compact, cost‑effective for low to medium head (up to 200 m).

  • Centerline support – handles thermal expansion up to 400°C without misalignment.

  • Back pull‑out design – allows seal, bearing, and rotor inspection without removing casing from piping.

  • Suitable for viscous and dirty fluids – open or semi‑open impeller options for particle passage (up to 6 mm solids).

  • API 682 seal compatibility – single, tandem, or double mechanical seals with appropriate quench/barrier plans. For hot bottoms, Plan 23 (cooled recirculation) or Plan 32 (external flush) is common.

  • Flow range – 5 to 2000 m³/h.

  • Head range – up to 200 m.

Typical OH2 applications

  • Atmospheric crude tower bottoms (topped crude)

  • Vacuum distillation flash zone bottoms (short resid)

  • Reboiler circulation pumps

  • Stripper bottoms (e.g., amine, glycol, sour water)


API 610 BB2 – Multistage Tower Bottom Pump

Structure match check: API 610 BB2 is defined as a horizontal, axially split, multistage, between‑bearings pump. This design is required when tower bottom pumps need higher heads (200-800 m) – for example, feeding downstream units like a vacuum furnace or sending bottoms to storage against high backpressure.

Why BB2 for tower bottom?

  • Multistage (2 to 10 stages) – achieves higher heads than OH2, up to 800 m.

  • Axially split casing – easy to inspect and clean without disturbing piping. Important for heavy, dirty fluids.

  • Between‑bearings rotor – superior shaft rigidity and bearing life under high radial loads (viscous fluids, off‑BEP operation).

  • High temperature capability – centerline support or foot‑mounted with expansion arrangements.

  • Material options – 12% chrome impeller/shaft for erosion resistance on dirty bottoms; duplex for corrosion.

  • Flow range – 20 to 2000 m³/h.

  • Head range – up to 800 m.

Typical BB2 applications

  • Vacuum residue charge to coker or visbreaker

  • Atmospheric residue to vacuum furnace feed

  • Heavy gas oil bottoms (FCC main fractionator)

  • High‑head transfer of hot resid to storage or downstream


Comparison & Selection Guide

FeatureOH2 (Single‑stage)BB2 (Multistage)
API 610 typeOH2 – horizontal overhung, foot-mounted, centerline supportBB2 – horizontal axially split, between-bearings, multistage
Head rangeUp to 200 m (typical)Up to 800 m
Flow range5 – 2000 m³/h20 – 2000 m³/h
Casing accessBack pull‑out (rotor only)Axially split – full internal access
Rotor supportOverhung (bearings on one end)Between‑bearings (bearings both ends)
Solids handlingImpeller options (open/semi‑open)Radial impellers (enclosed), limited solids
Best forLow head, moderate viscosity, moderate solidsHigh head, clean to moderate viscosity, low solids
MaintenanceQuick seal/impeller change without pipingFull casing split for inspection – longer downtime but easier cleaning

Key design features for both OH2 & BB2 (tower bottom service)

  • High temperature hydraulics – Centerline support (OH2) or expansion joints (BB2). Thermal growth compensation built in. Casing and bearings designed for continuous operation at 400°C.

  • Sealing for hot, heavy fluids – API 682 cartridge seals with Plan 23 (cooled recirculation for hot water/light oils) or Plan 32 (external flush with clean cool fluid) for heavy resid to prevent coking. Quench glands on the atmospheric side.

  • Viscosity handling – Hydraulic performance corrected for high viscosity (e.g., 10-1000 cSt). Impeller trimming may be required.

  • Erosion resistance – Impellers and wear rings in hardened 12% chrome or Stellite for bottoms containing catalyst fines or coke particles.

  • Materials – Carbon steel casing (WCB/WC6 up to 450°C). 12% chrome (CA15, CA6NM) for impeller/shaft. NACE MR0175 optional if sour bottoms.

  • Bearing cooling – For temperatures above 200°C, bearing housings require cooling water jackets or external fans. Option for pure oil mist lubrication.

Why choose our API 610 tower bottom pumps?

  • Full API 610 compliance – OH2 and BB2 types verified per standard. Performance, NPSH, mechanical run tests included.

  • High temperature reliability – Proper materials, thermal expansion design, and bearing cooling ensure long life.

  • Erosion and corrosion protection – Hardened trim, stainless/carbon steel options, and NACE compliance as needed.

  • Easy maintenance – OH2 back pull-out; BB2 axially split casing – both designed to reduce downtime.

  • Short lead time – Standard configurations ex-stock; custom designs 8-12 weeks.

  • Global spare parts support – Impellers, shafts, casings, bearings, seals shipped worldwide.

Quality assurance (both types)

  • ISO 9001:2015 certified.

  • API 610 mechanical run test (minimum 4 hours) with vibration and bearing temperature monitoring.

  • Hydrostatic test of casing.

  • Material traceability EN 10204 3.1 / 3.2.

  • NDE – MT, PT, UT as required.

  • Thermal growth analysis documented for high temperature service.

How to specify your tower bottom pump

Please provide: flow (m³/h), head (m), operating temperature (°C), specific gravity and viscosity (cSt at pumping temperature), solids content and size, NPSHa (m), fluid composition (crude, vacuum resid, FCC slurry, etc.), and H₂S content (for NACE). We will recommend OH2 or BB2 type, stage count (if BB2), impeller type (open/closed), seal plan, material class, and driver details.

Contact us

For a quotation or technical discussion on tower bottom pumps (API 610 OH2 or BB2) :

info@hyrig.com


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit