TEDA XQ29/1.8 Hydraulic Power Tong – Operation & Maintenance Manual

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
The TEDA XQ29/1.8 hydraulic power tong operation and maintenance manual provides practical field guidance. Standard operating procedures: installation (suspension, leveling, hose connection P/O, pull rope fixing), gear shifting (push for high speed, pull for low speed), make-up and break-out steps, and jaw changing. Daily maintenance: clean oil and dust after each use, grease rotating pins after transport, grease internal gears every 3 months. Keep oil temperature ≤65°C. No steam cleaning, no overpressure, no unauthorized modification. Common fault fixes: slipping jaws (change dies, clean, adjust brake), backup tong not clamping (check reset knob), misalignment (rotate knob 180°), easy disengagement (add shims). Safety rules: wear PPE, close safety door, cut hydraulic power before maintenance, fix pull rope correctly, no reverse operation, no touching moving parts. Contact info@hyrig.com.

Conatct For Details
DetailReview(0)Additional

Practical Field Guide – Easy to Learn

This manual provides clear, step-by-step instructions for operating and maintaining the TEDA XQ29/1.8 hydraulic power tong. Follow these procedures to ensure safe, efficient, and long-lasting performance.


I. Standard Operating Procedures

Installation Steps

  1. Suspend and fix the tong from the hoisting pulley

  2. Adjust to horizontal level

  3. Connect hydraulic hoses – P port (pressure inlet) / O port (return)

  4. Secure the rear pull rope

Gear Shifting

  • Operate only when the tong is moving slowly at low speed

  • Push the shift knob = High gear (fast spinning)

  • Pull the shift knob = Low gear (high torque)

Make-Up Operation (Tightening)

  1. Align the jaw opening with the pipe/rod

  2. Turn the selector knob to Make-Up position

  3. Push to engage clamping

  4. Run the operation until complete

  5. Reset and withdraw

Break-Out Operation (Loosening)

  1. Align the jaw opening with the pipe/rod

  2. Turn the selector knob to Break-Out position

  3. Push to engage clamping

  4. Run the operation until complete

  5. Reset and withdraw

Changing Jaws (Dies)

  1. Push and hold the jaw tight

  2. Remove the fixing pin

  3. Replace with the correct size jaws for the rod/tubing


II. Daily Maintenance Points

WhenAction
After each useClean oil and dust from surfaces. Grease all rotating pins and shafts.
After each transportClean with kerosene or diesel. Grease oil cups and gears.
Every 3 monthsOpen the cover plate. Grease internal gears.

Hydraulic System Requirements

  • Oil temperature must be ≤65°C

  • Keep hydraulic oil clean

  • Change oil regularly as per oilfield schedule

Prohibited Actions

  • Do not clean with steam

  • Do not exceed rated pressure or torque

  • Do not modify the equipment without authorization


III. Common Fault Troubleshooting

FaultQuick Fix
Main tong slipsChange jaws/dies → Clean debris → Adjust brake → Check and correct level
Backup tong does not clampCheck the reset knob direction and correct it
Jaw opening misalignmentRotate the selector knob 180° to reset
Premature disengagement during operationAdd shims to increase spring force

IV. Safety Rules – Red Lines

Must Follow

  • Wear full personal protective equipment (PPE) – hard hat, gloves, steel-toe boots

  • Close the safety door before operating

  • Cut hydraulic power before any maintenance or part replacement

  • Rear pull rope must be correctly fixed and tensioned

  • Keep hands away from moving parts during operation

Never Do

  • Do not operate in reverse direction

  • Do not touch moving components while tong is running

  • Do not bypass safety interlocks

  • Do not use damaged or worn jaws


Summary of Safe & Efficient Operation

  1. Install correctly – level, hoses secure, pull rope fixed

  2. Shift gears only at low speed – avoid transmission damage

  3. Use correct jaws – match rod/tubing size

  4. Clean and grease regularly – prevents premature wear

  5. Follow fault fixes – don't ignore small issues

  6. Respect safety rules – protect yourself and your crew


Contact Us

We supply the full TEDA power tong range, including all models and genuine spare parts.
For technical support, replacement parts, or on-site training, please contact us:

info@hyrig.com


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit