The XQ29/2.6 Hydraulic Sucker Rod Tong is a workover-specific sucker rod thread make-up and break-out device developed by Yancheng TEDA Drilling & Production Equipment Co., Ltd. It is an upgraded version of the XQ29/1.8. The unit is driven by a low-speed high-torque hydraulic motor with a manual control valve. The master tong delivers powerful torque, while the backup tong has a wrench‑type structure. It features dual‑speed operation (low gear for final tightening, high gear for fast spinning). The low gear provides high torque, making it especially suitable for breaking out stuck or corroded sucker rods. The overall structure is compact, simple, and lightweight (106 kg), offering easy and fast operation – ideal for routine workover sucker rod assembly and disassembly in oilfields.
| Parameter | Value |
|---|---|
| Applicable sucker rod sizes | CYG16, CYG19, CYG22, CYG25, CYG29 |
| High gear rated torque | 1.0 kN·m (700 ft·lb) |
| Low gear rated torque | 2.6 kN·m (1,900 ft·lb) |
| High gear max speed | 98 r/min |
| Low gear max speed | 32 r/min |
| Jaw opening | 62 mm (2.4″) |
| Dimensions (L×W×H) | 686 mm × 415 mm × 516 mm |
| Total weight | 106 kg (234 lb) |
| Rated system pressure | 10 MPa (1,450 PSI) |
| Max oil supply | 80 L/min (21 GPM) |
Strong power adaptability – Low‑gear high‑torque design easily handles stuck, rusted, or difficult sucker rod break-out.
Efficient and convenient operation – Dual‑speed shifting (high gear for fast spinning, low gear for final tightening) improves workover efficiency.
Practical and reliable structure – Small footprint, light weight, easy to install and move. Compatible with various workover rigs.
Safe and simple control – Manual control valve with direct drive, combined with safety door and limit design, reduces operational risks.
Operators must read and fully understand this manual and pass training before operating.
During operation, wear full PPE: coverall, safety boots, hard hat, protective gloves.
Correctly secure the tail rope as per manual – wrong direction is strictly prohibited.
Inspect equipment appearance, hydraulic hoses, safety door, dies, and slips – ensure no looseness or damage.
Keep work area free of debris and oil – ensure safe operating space.
Always stand on the jaw opening side – never face the rotating direction of the tong head.
During make-up and break-out, the safety door must be fully closed.
Never touch any moving parts while the equipment is running.
Operate strictly within rated parameters – no overpressure or over‑torque.
Shift gears only at low speed – prevent gear tooth damage.
Level the master and backup tongs before use – operation is prohibited if not level.
Before maintaining or replacing dies, jaw holders, seats, etc.:
Stop the hydraulic pump
Cut off power to the hydraulic tong
Do not add, remove, or modify any equipment components without authorization.
Use only genuine OEM parts – non‑standard substitutes are prohibited.
Hydraulic oil temperature must not exceed 65°C – prevents seal failure.
Keep hydraulic oil clean. Clean filter elements regularly. Replace oil immediately if contaminated.
Hydraulic hoses must be securely connected. Mark pressure port "P" and return port "O". Hose inner diameter ≥Φ20 mm.
Never operate the equipment if it has abnormal noise, leaks, or known defects.
Do not use steam to clean the equipment – prevents internal water ingress and oil starvation damage.
For lifting and transport, use wire rope ≥Φ12 mm. Lift smoothly – no tilting, swinging, or jerking.
For inquiries, technical support, or to order genuine spare parts, please contact us:
info@hyrig.com
We supply the full TEDA sucker rod tong range, including all models, spare parts, and safety accessories.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.