The ZQ127/25Y hydraulic drill pipe power tong is a heavy‑duty, open‑throat workover tool for make‑up and break‑out of drill pipe (2⅜"–3½"), tubing (3½"–4½"), and casing (4½"–5½"). To ensure continuous operation and minimize downtime, stocking the correct genuine TEDA wear parts is essential. This guide provides a complete spare parts list for one ZQ127/25Y unit, including mechanical wear components and O‑ring seals.
| No. | Part No. | Drawing No. | Part Name | Quantity |
|---|---|---|---|---|
| 1 | ZQ25-13 | ZQ25.1-3 | Centering roller shaft | 37 |
| 2 | ZQ25-14 | XYQ12.Z-03 | Centering roller | 37 |
| 3 | ZQ25-16 | GB68 | Slotted countersunk screw M5×10 | 79 |
| 4 | ZQ25-33 | GB1235 | O‑ring 28×2.4 | 2 |
| 5 | ZQ25-37 | GB1235 | O‑ring 24×2.4 | 8 |
| 6 | ZQ25-40 | GB1235 | O‑ring 36×3.5 | 4 |
| 7 | ZQ25-43 | GB1235 | O‑ring 32×3.5 | 2 |
| 8 | ZQ25-45 | GB1235 | O‑ring 38×3.5 | 2 |
| 9 | ZQ25-65 | XYQ12.Z-01.12(2-3) | Jaw dies | 24 each |
| 10 | ZQ25-72 | XYQ12.Z-48 | Roller | 16 |
| 11 | ZQ25-73 | XYQ12.Z-49 | Pin shaft | 16 |
| 12 | ZQ25-77 | GB1235 | O‑ring 63×5.7 | 16 |
| 13 | ZQ25-78 | — | Roller Φ10×30 | 168 |
| 14 | ZQ25-97 | GB1235 | O‑ring 40×3.1 | 2 |
| 15 | ZQ25-99 | GB1235 | O‑ring 80×3.1 | 2 |
| 16 | ZQ25-117 | ZQ25.1.8-2 | Friction plate | 6 |
| 17 | ZQ25-140 | GB1235 | O‑ring 45×3.1 | 8 |
| 18 | ZQ25-142 | GB1235 | O‑ring 22×2.4 | 8 |
| 19 | ZQ25-150 | GB1235 | O‑ring 50×3.1 | 2 |
| Size (mm) | Part No. | Quantity |
|---|---|---|
| 22×2.4 | ZQ25-142 | 8 |
| 24×2.4 | ZQ25-37 | 8 |
| 28×2.4 | ZQ25-33 | 2 |
| 32×3.5 | ZQ25-43 | 2 |
| 36×3.5 | ZQ25-40 | 4 |
| 38×3.5 | ZQ25-45 | 2 |
| 40×3.1 | ZQ25-97 | 2 |
| 45×3.1 | ZQ25-140 | 8 |
| 50×3.1 | ZQ25-150 | 2 |
| 63×5.7 | ZQ25-77 | 16 |
| 80×3.1 | ZQ25-99 | 2 |
Centering rollers & shafts (ZQ25-13, ZQ25-14) – High‑frequency wear items. Worn rollers cause poor pipe centering and uneven jaw gripping. Inspect after every major job.
Jaw dies (ZQ25-65) – Replace in matched sets. Choose the correct die size for the pipe diameter (2⅜"–3½" drill pipe, 3½"–4½" tubing, or 4½"–5½" casing). Stock 24 pieces of each type.
Friction plates (ZQ25-117) – Essential for braking performance. Replace when tong fails to hold position or when make‑up torque becomes inconsistent.
O‑rings (all sizes) – Seals age and leak over time. It is recommended to inspect O‑rings every well job or at least monthly. Replace any that show flattening, cuts, or hardening.
Rollers (ZQ25-72, ZQ25-78) and pin shafts (ZQ25-73) – These small parts are used in large quantities (168 small rollers per unit). Keep ample stock to avoid downtime from roller jamming or wear.
Important – Always use genuine TEDA original factory parts. Non‑genuine parts may cause improper fit, premature failure, unsafe operation, and will void the warranty.
| Part Category | Suggested Stock Level | Replacement Frequency |
|---|---|---|
| Jaw dies (ZQ25-65) | 24 each (full set) | Every 200–500 cycles |
| Friction plates (ZQ25-117) | 6 pieces | Every 6–12 months |
| O‑rings (all sizes) | As listed (1‑2 sets) | Annually or when leaking |
| Centering rollers (ZQ25-14) | 20–40 pieces | As needed (high wear) |
| Small rollers (ZQ25-78) | 50–100 pieces | Frequent replacement |
For genuine ZQ127/25Y wear parts, seal kits, or complete spare parts packages, please contact:
info@hyrig.com
*We offer fast response, original factory packaging, and technical support for all ZQ and XQ series power tongs (ZQ127/25Y, XQ89/3C, XQ114/9, XQ140/12A, and others).*
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.