236WCB Water Cooled Brake | Airflex Compatible Replacement

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
HYRIG can supply a compatible replacement for the EATON AIRFLEX 236WCB water cooled brake. The 236WCB is a two-plate, air-applied, water-cooled brake element designed for continuous slip and high-heat conditions on drawworks and workover rigs. Eaton Airflex® is a registered trademark of Eaton Corporation. HYRIG is an independent supplier of compatible replacement products and is not affiliated with, authorized by, or endorsed by Eaton Corporation.
Conatct For Details
DetailReview(0)Additional

Key Facts

AttributeValue
Product TypeAir-applied, water-cooled brake element
Compatible SeriesEATON AIRFLEX WCB / WCB2 configurations
Plate Configuration2 plates
DutyContinuous slip / high-heat braking
CoolingWater-cooled friction interface
Typical HostDrawworks, workover rigs
Designation MappingAlso referred to as 36WCB (inch)
Replacement CompatibilityForm-fit-function replacement; verify flange bolt pattern and water port thread

> Data source: Technical data table.

236WCB Specifications

ParameterValue
Size Designation236WCB (Size-code) / 36WCB (Inch)
Disc Diameter Basis36 in
Coolant Port1/4 SAE ORB
Typical Torque CapacityUp to 590,000 lb-in @ 80 psi (66,661 Nm @ 5.5 bar)
Typical WeightApprox. 3,250 lb / 1,474 kg housing
Variant NoteDual-acting WCB218/DA variants exist; confirm exact code on nameplate

Dimensions

Dimension ItemReference / Action
Disc Diameter Basis36 in (nominal, per model code)
Coolant Port Thread1/4 SAE ORB — match existing hose fittings
Mounting Flange Bolt PatternMeasure existing adapter hole spacing center-to-center
Overall Housing ProfileConfirm clearance dimensions against existing installation envelope
WeightApprox. 3,250 lb; confirm lifting plan

Structure / Working Principle

The 236WCB uses air pressure to clamp two friction discs against water-cooled wear plates. Coolant circulates through the jackets to carry away heat generated during continuous slip. This dual-disc design provides stable friction surface temperatures in sustained braking for drawworks and workover rigs.

Cross-Reference & Replacement

Replacing an Airflex WCB unit? Here is what to verify before ordering:

  1. Mounting flange bolt pattern — measure the existing hole spacing.
  2. Water port thread — confirm coolant line fitting standard (1/4 SAE ORB reference).
  3. Actuation type — confirm air tube vs. piston type.
  4. Friction disc wear — measure the existing discs. If below wear limit, replace the disc pack as a set.

Not sure which configuration you have? Send the existing unit's nameplate photo and flange measurements to HYRIG.

Compatible Host Models

The 236WCB is commonly used as a drawworks auxiliary brake. Compatible host configurations include:

  • Drawworks auxiliary braking systems
  • Workover rig draw-works with continuous slip braking requirements

> Host compatibility depends on flange and port configuration. Confirm your host model with HYRIG before order.

Internal links:

Applications

Suitable for drilling rig drawworks auxiliary braking and workover rig continuous slip braking where sustained heat generation requires water-cooled friction management.

Not intended for: emergency-stop-only applications where a dry friction brake is sufficient.

Selection Support

Not sure whether the 236WCB or 336WCB is the correct replacement? Send HYRIG the existing unit's nameplate photo, flange measurements, and water port thread size.

Frequently Asked Questions

Q: Is this an original Eaton Airflex product?
No. HYRIG supplies independent, compatible replacement products and is not affiliated with Eaton Corporation.

Q: What is the difference between 236WCB and 36WCB?
They refer to the same platform using different naming conventions (size code vs. inch). Confirm the exact code on your nameplate.

Q: Can I buy only the friction discs without the complete element?
Friction discs and wear plates are available as separate wear components; confirm the part number against the original drawing before ordering.

Q: What is the lead time for a 236WCB replacement?
Standard lead time is quoted per order based on configuration; for urgent downtime, confirm with HYRIG engineers at inquiry.

Contact

For 236WCB water cooled brake selection and compatible replacement parts, contact HYRIG: info@hyrig.com

What to include for fastest quote:

  • Existing unit nameplate photo
  • Mounting flange bolt pattern measurements
  • Water port thread type/size
  • Required quantity

Related Pages

Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit